Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Aluminum Z-clip 72 inch from Paramount Extrusions Company is an EA10812 Series interlocking long wall clip designed for panel assembly fittings. The 72 inch length gives a continuous mounting surface along cabinets or panels, which helps distribute the load across the wall. The extruded aluminum construction provides a rigid interlocking surface between wall and panel, which supports consistent engagement along the full run. The 1-5/8 inch width gives a broad bearing area on the wall side, which helps panels sit flat and aligned. Nine holes on 8 inch center-to-center spacing give repeated, predictable fastener locations, which supports straightforward layout and drilling on site. As part of a Z-clip system with a matching short hang clip, this long wall clip creates a simple lift-on and lift-off connection, which suits panel and cabinet jobs that may need removal for access or adjustment.
This EA10812 Series long wall clip mounts directly to the wall side of a panel assembly, which establishes the fixed reference for the interlocking connection. The nine pre-located holes on 8 inch centers define where fasteners engage the wall surface, which helps installers keep the clip straight as they work along the 72 inch length. The 1-5/8 inch width gives enough face area to sit solidly on typical wall substrates, which supports even load transfer when the short hang clip and attached panel engage. The 3/8 inch lift off is built into the interlocking profile, which controls how far the panel must be lifted to disengage from the wall clip. Used as the long wall member in a Z-clip pair, this part supports a repeatable fit each time the panel is hung or removed.
The long wall clip is designed to attach to the wall side of a cabinet or panel installation, which positions it as the fixed receiver in the Z-clip system. In this setup, the short hang clip attaches to the cabinet or panel, and the two interlock when the panel is lowered into place, which lets the installer set the wall line first and then hang panels to match. The 72 inch length suits runs where a continuous clip is preferred over multiple short sections, which can be useful on longer wall panels or grouped casework. The 1-5/8 inch width and extruded aluminum construction establish a defined seating surface along the wall, which helps the hanging components align consistently along the entire length of the assembly.
The EA10812 Series designation and 10812-6MH part number identify this specific extruded aluminum long wall clip geometry, which matters when matching it to the correct short hang clip in the same system. The interlocking aluminum profile creates a positive engagement between wall and panel, which supports repeatable positioning every time the panel is lifted on or off. The nine holes on 8 inch center-to-center spacing encourage an even pattern of wall fasteners, which helps distribute working loads and reduce point stresses along the clip. The 3/8 inch lift off characteristic defines the vertical travel needed to clear the interlock, which gives installers a consistent expectation when removing or rehanging panels for service access. By combining a fixed long wall clip with a matching short hang clip, this Z-clip arrangement supports efficient installation and later adjustment without disturbing the established wall layout.
The EA10812 long wall Z-clip attaches to the wall side of a panel assembly, creating the fixed interlocking surface that receives the matching short hang clip on the cabinet or panel.
The 72 inch long wall clip provides a continuous mounting track along the wall, which supports longer panels or grouped cabinets on a single straight reference line.
The 3/8 inch lift off describes the vertical clearance built into the interlocking profile, allowing panels to be lifted upward that distance to disengage from the wall clip.
Holes on 8 inch center-to-center spacing offer a regular pattern for wall fasteners, helping installers maintain straight alignment and even load distribution along the 72 inch clip.
The long wall clip and short hang clip form an interlocking aluminum pair, where the panel-mounted short clip drops into the wall-mounted long clip to secure the assembly.
The 10812-6MH part number identifies this specific EA10812 Series 72 inch extruded aluminum long wall clip, helping match it to drawings or standard panel assembly details.
The Paramount Extrusions Company EA10812 Series long wall clip combines a 72 inch length, 1-5/8 inch width, and nine holes on 8 inch centers to serve demanding panel assembly fittings. The interlocking aluminum profile with 3/8 inch lift off works with a short hang clip to create a stable lift-on, lift-off connection between wall and panel. For projects calling for an extruded aluminum long wall Z-clip with these specific dimensions and EA10812 geometry, this 10812-6MH part from Wurth Baer Supply offers a clear match to that requirement.
Sold In: 1 Each