Hickory Hardware Williamsburg Series 3" (76 mm) Center to Center Chrome Pull, - P3050-CH

Hickory Hardware Williamsburg Pull For Cabinets

Hickory Hardware Williamsburg pull gives a straightforward zinc cabinet handle for projects that call for the P3050-CH part. This Belwith Keeler piece uses a chrome finish that creates a bright, clean look on doors or drawers in workrooms and living spaces alike.

The pull is built around a 3 inch center to center mounting dimension, so the hole pattern lines up with many standard layouts for cabinet fronts. Overall length is 3-3/8 inches, which keeps the footprint compact while still providing enough bar length for a confident grip when opening heavier drawers or doors.

A projection of 1-1/4 inches sets the hand clearance off the face of the cabinet, helping fingers catch the pull without rubbing the surface. The 1/2 inch width gives a slim profile, so the hardware reads visually light while still marking the front as the working edge of the cabinet.

Practical Details Of This Chrome Cabinet Pull

• The 3 inch center to center dimension sets a clear drilling layout, which helps installers position the pull accurately on new cabinet faces or line up with existing holes during change-outs.
• The 3-3/8 inch overall length keeps the pull compact on narrow drawer fronts, which matters when laying out multiple pulls in tight banks where crowding could complicate spacing.
• The 1-1/4 inch projection holds hands away from the cabinet surface, which reduces knuckle contact during use and limits wear on painted or laminated finishes at the pull points.
• The 1/2 inch width keeps the pull visually light across the front, which supports clean lines on modern or traditional fronts without overpowering smaller cabinet doors.
• The chrome finish delivers a bright metallic surface, which coordinates with other chrome hardware in a room so the cabinetry ties into hinges, faucets, or other chrome elements.
• The zinc material provides a solid base for the hardware, which supports everyday opening and closing cycles on doors and drawers across the installation.

Installation And Fit Details For P3050-CH Pull

The P3050-CH cabinet pull centers on a 3 inch center to center measurement, so installers can work from a known spacing when drilling new fronts or aligning with existing 3 inch on-center holes. That standard layout simplifies jig setup and repeat drilling across a run of cabinets.

The 3-3/8 inch overall length follows from the 3 inch hole spacing, giving just enough material beyond the posts to frame the grip. With a 1-1/4 inch projection, the hardware stands off the face at a distance that balances hand clearance with a tidy profile, which is useful when doors open near walls or adjacent cabinets.

A width of 1/2 inch defines a narrow bar across the front, which lets installers position the pull confidently on rails or narrow stiles without crowding panel details. The chrome finish on the zinc construction offers a consistent surface that reads clean across multiple pulls in a run.

How This Williamsburg Chrome Pull Works In Projects

Using The Williamsburg Pull Across Cabinets

This Hickory Hardware Williamsburg collection pull is presented for cabinet applications where a simple 3 inch center to center layout is needed. On multipurpose room cabinets, that standard spacing lets installers repeat the same drilling pattern from cabinet to cabinet, which keeps workflow steady and predictable.

In den or storage drawers, the 3-3/8 inch overall length fits comfortably on small to medium fronts, so multiple drawers can carry the same P3050-CH pull without overcrowding face frames. The chrome finish pairs with other chrome cabinet hardware and decorative elements, which helps tie together cabinetry and surrounding fixtures in one consistent visual line.

The 1-1/4 inch projection supports everyday gripping on deeper drawers by pulling hands out from the face, which can help users get leverage on loaded storage drawers. Because the width is held to 1/2 inch, the pull leaves more face area visible, which is helpful when the cabinet design or wood grain is part of the visual focus.

Details That Support Repeatable Mounting Results

The 3 inch center to center dimension on this Belwith Keeler P3050-CH pull aligns with many cabinet templates, which means installers can set stops once on drilling jigs and repeat the same hole spacing along an entire wall of cabinets. That repeatability cuts layout time and supports clean visual alignment.

The 3-3/8 inch length gives consistent end distances beyond the mounting points, so when pulls are lined up along multiple drawers, the hardware edges track in straight lines that read uniform. The 1-1/4 inch projection defines a predictable stand-off that helps doors clear adjacent surfaces during opening because the gripping point is set consistently away from the face.

With a 1/2 inch width, the pull sits neatly on narrow rails, which lets installers center it on trim elements without overlapping edges. The chrome finish across the zinc body presents a uniform appearance from pull to pull, which matters when projects call for repeating the same hardware style throughout a room or across connected spaces.

Key Questions About This Williamsburg Cabinet Pull

Choose This Pull For Standard 3 Inch Layouts

This Hickory Hardware Williamsburg pull with 3 inch center to center mounting, 3-3/8 inch overall length, and 1-1/4 inch projection gives a clear set of dimensions for planning cabinet hardware layouts. The chrome finish over zinc delivers a consistent cabinet pull appearance in the P3050-CH part number.