32mm center to center pull defines this Schwinn Hardware handle as a compact option that spaces its mounting points at 32 mm, which suits layouts built around the common 32 mm system for consistent drilling and repeatable cabinet runs. The Schwinn 2935 Series 1-1/4 in (32 mm) center to center matte gold pull identifies the product as part of the Schwinn 2935 family, which helps match this piece visually with other handles and pulls in the same series across a project. The Schwinn Hardware brand ties this pull directly to a manufacturer focused on decorative hardware and moldings, which matters when standardizing hardware across different jobs. Its web description as a clean, modern, matte gold pull highlights the streamlined look that fits contemporary cabinet and casework designs. The note that this is a Schwinn original design signals a distinctive profile that supports uniform styling on visible fronts.
The 32 mm center to center dimension in the product name directly defines the mounting hole spacing, which allows installers to align drilling jigs or boring equipment to a known measurement when setting up repetitive runs. Listing this as a 1-1/4 in (32 mm) center to center matte gold pull translates the metric spacing into an imperial reference, which helps bridge drawings or site notes that switch between systems. As a compact pull referenced as 2 inch square, it occupies a modest footprint on the face of the cabinet, which leaves room for edge clearances and neighboring hardware on narrow rails or stiles. Positioning it within handles and pulls, Schwinn Hardware signals a standard pull interface that suits typical cabinet and drawer faces where a simple two-point mount fits established shop workflows.
The web description calling this a clean, modern, matte gold pull, 2 inch square, points to use on contemporary cabinet fronts where straight lines and compact forms are preferred, such as kitchen, bath, or built-in storage. Its 32 mm center to center layout suits cabinet runs built around the 32 mm system, which is common in many commercial and residential casework operations using line-boring equipment. The product name highlighting a 1-1/4 in (32 mm) center to center matte gold pull gives both imperial and metric cues, supporting project documentation that may specify either unit. Being categorized as decorative hardware and moldings under handles and pulls clarifies that this part is intended for visible faces, where both appearance and grip position influence user interaction with doors and drawers.
The explicit 32 mm center to center measurement provides a fixed dimension for jig placement, which supports consistent drilling and reduces layout variation from cabinet to cabinet. Referencing the pull as 2 inch square gives a sense of its overall footprint, allowing planners to position it so that edges, rails, and neighboring pulls maintain even spacing across a bank of fronts. The SAP description, 32MM C/C PULL, MATTE GOLD FINISH, reinforces both the spacing and the surface treatment in a concise way, which helps during ordering or reordering when part numbers and descriptions must match hardware already installed. The manufacturer part number 59338 precisely identifies this Schwinn 2935 Series pull, which matters when aligning replacement or expansion work to an existing installation that already uses this specific design.
The 32 mm center to center on this pull defines the distance between its mounting holes, which guides drilling patterns and aligns with 32 mm system cabinet layouts.
The matte gold finish gives the pull a muted gold tone, which supports clean, modern cabinet designs where a softer metallic look is preferred over high gloss.
The 2 inch square description indicates a compact, roughly square pull footprint, which helps it fit smaller doors and drawers without overwhelming the cabinet face.
This pull is identified as Schwinn 2935 Series, so it aligns visually with other pieces in the same series when coordinating handles and pulls on a project.
The Schwinn Hardware brand links this pull to a dedicated decorative hardware manufacturer, which helps standardize cabinet hardware on professional woodworking jobs.
The manufacturer part number 59338 uniquely identifies this 32 mm center to center matte gold pull, which supports accurate ordering and matching for follow-up projects.
The 32 mm center to center layout, compact 2 inch square form, and matte gold finish combine to define this Schwinn 2935 Series pull as a concise solution for modern cabinets. Its classification under decorative hardware and moldings, handles and pulls, positions it as a primary gripping point wherever a streamlined look is required. The clear designation as a Schwinn original design and the precise part number 59338 help align new work, expansions, or replacements around a single, repeatable hardware choice. For projects built on the 32 mm system that call for a clean, modern, matte gold pull, this piece offers a defined dimension and finish to plan layouts confidently.