Mortising Router Bit, 3/4" Diameter, 1/4" Shank, 2" Length

Freud Mortising Bit 3/4 Inch For Clean Cuts

Freud mortising bit 3/4 inch is a straight mortising router bit designed to cut clean, precise, splinter free mortises in plywood, veneer, solid wood or almost any composite material, so hinge pockets and hardware recesses stay sharp and professional. The 3/4 inch diameter matches common mortise widths, helping you size slots and grooves accurately for cabinet, furniture, or architectural work. A 1/4 inch shank connects this router bit to compatible routers, tying directly into compact or mid-size routing setups on CNC, hand-held or table-mounted tools. The 2 inch length gives working reach for typical mortise depths and for cutting grooves and dadoes in casework and frames. As part of the Freud Tool mortising bit line, this router bit is built specifically for straight mortising tasks rather than general profiling, helping you focus on accurate joinery and hardware installation.

Key Freud Mortising Router Bit Work Advantages

• The down shear design on most Freud mortising bits pushes wood fibers downward during the cut, which produces clean top surfaces that reduce edge sanding and touch-up around mortises, grooves, and hinge recesses.
• Deep center gullets are engineered into this mortising bit to provide maximum material removal without chip loading, so chips clear efficiently and cuts stay smooth during deeper mortises in plywood, veneer, solid wood or composite materials.
• Design for splinter free mortises in plywood, veneer, solid wood or almost any composite material helps maintain crisp edges around hinge gains and hardware pockets, supporting tight-fitting installations in visible cabinet and furniture surfaces.
• Suitability for cutting grooves and dadoes allows this mortising bit to handle both joinery slots and hardware recess work, which keeps setup simple when alternating between mortises, grooves, and dadoes on the same project.
• Use on CNC, hand-held and table-mounted portable routers means this Freud mortising router bit adapts to shop or jobsite setups, supporting consistent mortise quality whether the work is done on a machine, bench, or installed piece.

Router Bit Fit, Diameter, And Shank Details

This Freud mortising router bit uses a 3/4 inch diameter cutting profile that sets the width of mortises, grooves and dadoes, making it well suited to wider hinge leaves and structural slots in frames or panels. The 1/4 inch shank connects to routers using that collet size, aligning this bit with many portable and table-mounted routers in cabinet and woodworking shops. Overall 2 inch length supports typical mortise depths and groove patterns, giving enough reach for recessed hardware work without excessive overhang during cuts. As a straight mortising router bit in the Freud Tool product class, it focuses on plunging and straight-line passes rather than edge shaping, which streamlines setup for repeatable mortising runs.

Using This Straight Mortising Bit In Real Work

Where This Mortising Router Bit Performs Best

This Freud mortising bit is designed for cutting mortises in plywood, veneer, solid wood or almost any composite material, so it fits well into cabinet building, furniture construction, and architectural trim work where multiple sheet goods and hardwoods appear on the same job. Its straight mortising design targets hinge and hardware mortising, providing accurate recesses for hinges and hardware where depth and edge quality directly affect alignment. The ability to cut grooves and dadoes extends its use into building case sides, shelves, and frame members, allowing the same 3/4 inch diameter to define joint locations and hardware channels. Because it can be used in CNC, hand-held and table-mounted portable routers, this bit supports both production CNC runs and one-off field adjustments using the same cutting geometry.

Details That Support Accurate Mortising Results

The down shear design on most Freud mortising bits directs fibers downward, which keeps the top surface of plywood, veneer, solid wood or composite panels cleaner as the bit plunges and moves, limiting splintering along the mortise edges. Deep center gullets are built to move material away from the cutting edges quickly, reducing chip loading during deeper passes and allowing the bit to maintain cutting efficiency when forming mortises, grooves, and dadoes. A 3/4 inch diameter cutting profile establishes a consistent mortise width, helping hinge leaves and related hardware seat evenly across the length of the recess. The 1/4 inch shank ties this geometry to routers that accept that shank size, supporting stable rotation in CNC, hand-held or table-mounted routers. Freud Mortising Bits are designed to deliver precise, splinter free mortises, which supports joinery and hardware installations that rely on straight walls and smooth bottoms for fit and appearance.

Common Questions About The Freud 16-104 Mortising Bit

Select This Mortising Bit For Clean, Precise Work

The Freud Tool Mortising Router Bit, with 3/4 inch diameter, 1/4 inch shank and 2 inch length, is designed for precise, splinter free mortises in plywood, veneer, solid wood or composite materials, supporting accurate hinge, hardware, groove and dado work. Its down shear design on most bits and deep center gullets work together to keep top surfaces cleaner and chip flow efficient, which helps cuts stay accurate across multiple passes. Designed for use in CNC, hand-held and table-mounted portable routers, this straight mortising router bit gives you a consistent cutting profile for cabinet, furniture, and architectural projects where reliable mortises and grooves matter.