4 Inch Francisco Pull Satin Nickel For Cabinets

4 inch Francisco pull satin nickel describes a cabinet and drawer handle from the Francisco collection designed for a clean, coordinated look across a project. The Liberty Hardware design uses zinc die cast construction, which provides a solid metal feel that works well for everyday cabinet and drawer use. Its satin nickel finish offers a muted metallic appearance that suits many kitchen, bath, and shop environments where a modern but not flashy look is preferred. The pull measures 4.94 inches in overall length, so it spans the front of typical cabinet doors or drawers comfortably without dominating narrow faces. A projection of 1.18 inches sets the grip out from the surface enough for fingers to hook behind it in normal reach positions. The 0.71 inch width keeps the handle visually slim while still giving enough surface for a steady, predictable pull.

Key Francisco Collection Details That Help On Site

• The 4 inch center to center drilling lets this pull replace many standard cabinet and drawer handles without changing hole locations, which supports straightforward swaps on finished doors and fronts.
• The 4.94 inch overall length gives a balanced look on medium-width doors and drawers, helping rows of fronts line up visually when multiple pulls are installed across a run.
• The 1.18 inch projection creates hand clearance between the pull and the cabinet surface, which aids comfortable gripping even on thicker door edges or applied drawer fronts.
• The 0.71 inch width keeps the profile narrow, which can reduce visual clutter on smaller doors while still providing a defined edge for pulling.
• The zinc die cast material creates a metal body suited to repeated opening and closing, supporting consistent operation on frequently used cabinets.
• The satin nickel finish provides a soft metallic tone that coordinates with many hinges and fixtures finished in similar nickel shades.

Mounting And Fit Details For This Cabinet Pull

This Liberty Hardware cabinet pull is drilled on a 4 inch center to center pattern, which aligns with a common layout for face frame and frameless cabinet doors and drawers. That fixed spacing allows installers to use standard 4 inch boring jigs or templates so hole placement can stay uniform across a bank of cabinets. The manufacturer part number P29617-SN-C identifies this specific Francisco collection pull in satin nickel, which keeps ordering consistent when repeating the same handle style on later phases or matching existing hardware. With a length of 4.94 inches from end to end, the pull suits many base, wall, and tall cabinet faces where a mid-length handle is preferred over knobs or longer bars.

Using This Liberty Hardware Pull In Real Projects

Where This Francisco Collection Cabinet Pull Fits Best

This Francisco collection cabinet handle works in decorative hardware and moldings applications where a 4 inch center to center handle is specified, covering many kitchen, bath, and built-in cabinet layouts. The zinc die cast construction allows the pull to function as a primary handle on both doors and drawers in frequently used areas. Its satin nickel finish lets it coordinate with other satin nickel cabinet hardware across a room, supporting a consistent appearance from wall cabinets to base units. Because the pull belongs to Liberty Hardware, it fits into projects that already rely on this brand for decorative hardware and moldings, helping maintain a unified product line across multiple installs. The combination of 4 inch center spacing and 4.94 inch overall length makes this pull practical on medium-width drawer fronts and doors, where it offers enough hand contact without reaching too close to the panel edges.

Details That Support Consistent Alignment And Repeats

The 4 inch center to center measurement on this Liberty Hardware cabinet pull allows installers to repeat drilling patterns across large banks of cabinets, which supports straight sight lines when viewing rows of hardware. Its 1.18 inch projection provides a consistent standoff from the cabinet face, so pulls sit in a uniform plane along tall pantry doors, wide drawers, and narrow wall cabinets. The 0.71 inch width helps keep pulls aligned visually because the narrower bar leaves clear margins to stiles and rails on most door designs. The satin nickel finish from the Francisco collection keeps color and sheen consistent, which is useful when hardware runs across joined cabinet sections or into adjacent rooms. The manufacturer part number P29617-SN-C gives a clear identifier for reorders, so matching pulls can be used on future additions or replacement fronts without shifting style or finish. Overall, the size and finish details support repeatable layouts that look intentional from one cabinet run to the next.

Common Questions About This Francisco Cabinet Pull

Select This Pull For 4 Inch Cabinet Layouts

The 4 inch center to center pull from Liberty Hardware offers a straightforward option when a Francisco collection handle in satin nickel is specified. Its zinc die cast body, 4.94 inch overall length, and 1.18 inch projection support everyday cabinet and drawer use across kitchens, baths, and built-ins. The satin nickel finish and 0.71 inch width help maintain a clean, coordinated look on projects using decorative hardware and moldings in similar tones. For jobs built around 4 inch hole spacing and a mid-length handle, the P29617-SN-C cabinet pull provides a consistent, repeatable choice.