Berenson Edge Pull Series 1" (25 mm) Center to Center Satin Nickel Tab Pull, - 9000-4BNL-P
Description
Berenson Edge Pull 1 Inch Center To Center Use
Berenson Edge Pull 1 inch center to center gives cabinets a low-profile grip using only a 1 inch (25 mm) mounting span, which suits narrow drawer fronts or tight layouts where larger pulls crowd the face. The pull comes from the Advantage Two Series, so each piece follows the same design language for projects needing a consistent modern look across multiple fronts. Aluminum construction keeps the part light while still providing a solid feel at the hand contact point, which helps during frequent opening cycles in busy areas. The brushed nickel finish presents as a satin-style surface that reduces visual fingerprints compared to highly polished metal, which helps cabinets maintain a clean appearance between wipe-downs. A projection of 1-21/32 inches sets the hand out from the fascia just enough for a comfortable pinch grip, which supports quick access without overhanging the front.
Key Berenson Advantage Two Edge Pull Details
- The 1 inch center to center dimension concentrates mounting holes into a tight span, which is useful on small drawer fronts or narrow rails where space for hardware is limited yet alignment still matters.
- A total length of 1-25/32 inches keeps the tab compact, which reduces visual clutter on minimalist cabinets while still marking a clear grab point for everyday operation.
- A 3/4 inch width and 3/4 inch base diameter present a balanced face, which helps the pull sit proportionally on standard cabinet rail widths and supports a symmetrical hardware layout.
- The 1-21/32 inch projection holds the gripping edge away from the cabinet surface, which creates finger clearance for a secure pull stroke without risking knuckle contact with the door.
- The brushed nickel finish on aluminum delivers a satin nickel look, which coordinates with common appliance and hinge finishes so hardware appearance remains consistent across the installation.
Edge Pull Mounting Measurements And Fit
The 1 inch center to center mounting dimension defines the drilling layout, so installers can set hole spacing accurately when templating or using a jig across multiple fronts. Overall length at 1-25/32 inches keeps the pull shorter than many standard handles, which lets it fit on narrow frames or small drawer faces where traditional bar pulls would extend too far. A 3/4 inch width and base diameter provide enough footprint at the mounting area to distribute load, which supports firm tightening without concentrating force on an overly small contact patch. Projection of 1-21/32 inches establishes the stand-off distance from the cabinet face, which affects both hand clearance and how far the pull visually steps off the surface in elevation views.
Using This Berenson Satin Nickel Tab Pull
Where This 25.4mm Edge Pull Works Best
The Advantage Two Series identity links this pull to a broader decorative hardware collection, which benefits projects aiming to run the same design on doors, drawers, and panels in one space. With a 1 inch center to center drilling span, the pull is suited to smaller cabinet fronts, which often appear in kitchen, bath, or furniture pieces where full-size handles would dominate the facade. The 3/4 inch width lets the pull sit comfortably on face-frame rails or frameless edges, which supports parallel alignment along the top or side of door and drawer fronts. Because the aluminum body carries a brushed nickel finish described as satin nickel, the pull visually ties in with many hinges and fixtures labeled in similar tones, which maintains a unified metal color across a run of cabinets.
Why These Dimensions Support Consistent Results
The specified 1 inch center to center measurement repeats exactly from part to part, which helps installers build or reuse drilling templates so every pull lands level across multiple cabinets. Overall length of 1-25/32 inches means the hardware does not overrun the corner when mounted as a tab at the edge, which keeps the pull clearly accessible while preserving clean cabinet lines. A base diameter and width both at 3/4 inch create a predictable footprint for screw placement relative to door thickness, which helps the hardware sit flush when tightened against common panel constructions. The 1-21/32 inch projection sets a constant stand-off that informs reveal planning between adjacent fronts, which can reduce interference when doors and drawers are arranged in tight grids. The aluminum material behind the brushed nickel finish keeps weight down, which is helpful when many pulls are used across large installations where cumulative hardware mass can affect operation feel.
Common Questions About This Berenson Edge Pull
What center to center size does this edge pull use?
The Berenson edge pull uses a 1 inch center to center spacing, which sets the hole layout for drilling jigs and ensures consistent knob alignment across doors and drawers.
How far does the tab pull project from the cabinet face?
The tab pull projects 1-21/32 inches from the cabinet face, which gives fingers clearance to grip without extending excessively into walkways or tight spaces.
What material is the Advantage Two Series tab pull made from?
The Advantage Two Series tab pull is made from aluminum, which keeps the hardware light while still providing a solid contact point for regular cabinet use.
What finish does the 9000-4BNL-P edge pull have?
The 9000-4BNL-P edge pull has a brushed nickel finish described as satin nickel, which coordinates with many contemporary hinges, faucets, and appliance trims.
What are the overall length and width of this tab pull?
This tab pull has a length of 1-25/32 inches and a width of 3/4 inch, which suits narrow cabinet rails and smaller drawer fronts where compact hardware is preferred.
Which collection does this Berenson edge pull belong to?
This Berenson edge pull belongs to the Advantage Two Series collection, which helps maintain a consistent decorative style across an entire cabinet project.
Selecting This Edge Pull For Your Project
The Berenson Edge Pull 1 inch center to center combines a compact 1-25/32 inch length with 3/4 inch width, which works well on smaller cabinet fronts needing a modern tab profile. Aluminum construction with a brushed nickel, satin-style finish keeps the look consistent with many contemporary metal tones, which supports coordinated hardware throughout a room. Defined dimensions for center to center, projection, and base diameter simplify layout work, which helps installers repeat accurate placement across doors and drawers in a run. For projects calling for Advantage Two Series styling in a small-format pull, this 9000-4BNL-P model from Wurth Baer Supply aligns size, finish, and mounting measurements in one part.