Berenson Transitional Advantage One Series 3-3/4" (96 mm) Center to Center Polished Chrome Pull, - 9172-1026-P

Berenson Transitional Advantage One Pull For Cabinets

Berenson Transitional Advantage One pull gives cabinets a defined grasp point using a 3-25/32 inch center to center dimension, so installers can line up multiple pulls with consistent spacing on doors and drawers. The polished chrome finish puts a bright, reflective surface on the zinc material, which helps this pull visually coordinate with other polished chrome decorative hardware in the same space. The 6-3/16 inch overall length provides enough bar length for fingers to clear the door edge, which supports comfortable everyday opening and closing. A projection of 1-5/32 inch stands the pull off the front of the cabinet, creating hand clearance between the hardware and the surface. The 1-1/4 inch width offers a stable grip area across the front face, which suits both smaller and larger hands in busy kitchens or workrooms.

Key Berenson 9172-1026-P Pull Details

• The 3-25/32 inch center to center drilling dimension sets fixed hole spacing, which streamlines layout work when aligning this pull across multiple cabinet fronts in a run.
• The 6-3/16 inch length establishes the overall footprint of the pull, which helps with planning proportional placement on wider doors or drawer fronts.
• The 1-5/32 inch projection defines how far the pull stands off the surface, which affects finger clearance and reduces knuckle contact against the cabinet face during operation.
• The 1-1/4 inch width describes the front face size, giving a broad contact area that helps distribute force when pulling heavier drawers or loaded cabinet doors.
• The polished chrome finish on zinc offers a bright metallic look, which supports design continuity with other polished chrome handles and pulls in the same installation.
• The Advantage Series classification identifies this pull as part of Berenson Corporation decorative hardware, which helps match style and finish across a full job.

Installation And Fit Details For This Cabinet Pull

The 3-25/32 inch center to center measurement defines the drilling pattern for this cabinet pull, so installers can use that dimension when boring through cabinet doors or drawer fronts. Using the 6-3/16 inch overall length as a reference helps position the pull so it sits proportionally on narrow or wide fronts. The 1-5/32 inch projection indicates how far the hand will sit off the surface, which is useful when working around face frames or adjacent doors. With a 1-1/4 inch width, the pull presents a solid front edge, which can be important when aligning multiple pulls so their edges visually line up across a bank of cabinets. The polished chrome finish on the zinc material supports a clean look on painted or laminated fronts in kitchens, baths, or shop cabinetry.

Using This 96 Mm Center To Center Cabinet Pull

Where This Polished Chrome Cabinet Pull Works

This polished chrome cabinet pull uses a 3-25/32 inch center to center drilling size, so it suits doors and drawers designed around that hole spacing. The 6-3/16 inch overall length lets this pull span a comfortable portion of typical kitchen and bath drawer fronts, which helps with reach when opening wider drawers. With a 1-1/4 inch width and 1-5/32 inch projection, the pull creates a defined handhold on cabinet faces, which is practical in utility areas where users often grab hardware quickly with wet or gloved hands. The polished chrome finish on zinc coordinates with other polished chrome decorative hardware and moldings, so this pull can be used as part of a unified hardware layout across a room. As a member of the Advantage Series from Berenson Corporation, it fits projects that call for consistent style and finish across multiple cabinets.

Details That Support Consistent Cabinet Hardware Results

The 3-25/32 inch center to center measurement on the Berenson Transitional Advantage One pull supplies a precise drilling target, which reduces layout variation when repeating the pull across a full kitchen or office installation. The 6-3/16 inch length helps installers visually balance the pull relative to door height or drawer width, limiting the need to adjust layouts later. A projection of 1-5/32 inch provides enough stand-off from the surface to clear typical door and drawer profiles, which helps avoid hands dragging against the cabinet finish during use. The 1-1/4 inch width gives a stable gripping surface, supporting smoother action when pulling heavier loads out of base cabinets. Using the polished chrome finish as a reference point makes it straightforward to coordinate hinges, knobs, and other handles in the same polished chrome appearance. The zinc material described for this pull provides a defined substrate for the polished chrome finish, which contributes to a consistent look across multiple pieces on the same job.

Common Questions About This Berenson Cabinet Pull

Select This Pull For Center To Center Layouts

The Berenson Transitional Advantage One pull combines a 3-25/32 inch center to center drilling pattern with a 6-3/16 inch overall length, giving both layout and visual balance for cabinet fronts. With a 1-5/32 inch projection and 1-1/4 inch width, the pull defines a clear gripping surface that supports regular door and drawer use. The polished chrome finish on zinc aligns with polished chrome decorative hardware and moldings offered through Wurth Baer Supply, which helps installers keep a unified appearance across cabinetry on residential or commercial projects.