Berenson Transitional Advantage One Pull For Cabinets

Berenson Transitional Advantage One pull gives you a 5-1/16 inch (128 mm) center to center handle that works anywhere you need a consistent drill pattern on doors or drawers. The pull is part of the Advantage Series, so it keeps styling and sizing in line with the rest of the collection across a job. Its polished chrome finish provides a bright, reflective look that suits transitional cabinet designs where a clean metal tone is important. The pull is made from zinc, giving you a metal body suitable for everyday cabinet use. Overall length is 7-25/32 inches, so the handle spans wider than the drilling pattern and visually anchors medium-width fronts. Projection of 1-3/16 inches sets the grip off the surface enough for fingers to wrap comfortably during regular use in kitchens, baths, or shop cabinets.

Key Pull Details That Support Cabinet Work

• The 5-1/16 inch (128 mm) center to center measurement lets you lay out drilled holes using a common metric and inch spacing, which helps keep multiple fronts aligned on larger cabinet runs.
• The 7-25/32 inch overall length gives this pull a proportion suited to standard cabinet doors and drawers, so hardware looks balanced instead of undersized or oversized across typical face widths.
• The 1-3/16 inch projection sets the handle away from the surface so fingers clear the door or drawer face during operation, which reduces knuckle contact on frequently used cabinets.
• The 15/32 inch width keeps the pull visually lighter while still offering a defined edge to grab, which can help when spacing several pulls across banks of drawers.
• The 5/16 inch base diameter creates a compact footprint at each mounting point, which is useful when you need the pull to sit within narrow frame or rail sections.
• The polished chrome finish provides a smooth, reflective surface that matches other polished chrome decorative hardware, simplifying finish coordination on a job.

Mounting Size And Center To Center Alignment

This Berenson 9177-1026-P pull uses a 5-1/16 inch (128 mm) center to center layout, so your mounting holes align with standard 128 mm drilling jigs in the shop or onsite. That spacing lets you reuse existing 128 mm centers when swapping older handles, reducing extra boring on retrofit work. Its 7-25/32 inch length leaves material beyond each hole, which helps cover minor chipping at the bore edge. The pull projects 1-3/16 inches off the face, setting a consistent stand-off that matches common cabinet hardware depths. With a 15/32 inch width, the handle offers a defined gripping bar without crowding narrow rail sections, which matters when you are working with face frames or slim slab fronts.

Using This Polished Chrome Pull In Projects

Where This Berenson Cabinet Pull Fits Best

The Berenson Transitional Advantage One Series 9177-1026-P pull is a fit for cabinets needing a 5-1/16 inch (128 mm) center to center handle, so it serves both new layouts and replacements using that pattern. Its polished chrome finish ties in with other polished chrome decorative hardware on doors and drawers, keeping finish lines consistent from one cabinet bank to another. At 7-25/32 inches long, the pull spans enough of the front to visually anchor on kitchen, bath, or shop cabinets that use standard door and drawer widths. The 15/32 inch width keeps the bar slim, which works well on modern and transitional fronts where a lower-profile handle is preferred. With a base diameter of 5/16 inch, the pull sits neatly on rails or stiles without overlapping trim details.

Why These Dimensions Support Repeatable Cabinet Results

The 128 mm center to center dimension on this Berenson Transitional Advantage One pull matches a common drilling standard, allowing repeatable hole placement across multiple fronts using the same jig setup. That consistency speeds runs of doors and drawers because you can keep the jig locked on the 128 mm spacing instead of changing between patterns. Projection of 1-3/16 inches sets a predictable clearance for fingers behind the bar, which helps avoid contact with the door or drawer face during daily operation and keeps fronts cleaner. The 7-25/32 inch overall length ensures the pull covers any slight variations at the bored holes from drilling, which can help on site-finished or pre-finished work. Width at 15/32 inch offers a grip that feels defined but not bulky, supporting precise placement in layouts where multiple pulls line up horizontally or vertically. Combined with the polished chrome finish and zinc construction, these dimensions give installers a consistent hardware piece that repeats well across small or large cabinet projects.

Common Questions About This Berenson Cabinet Pull

Select This Pull For 128 Mm Cabinet Layouts

The Berenson Transitional Advantage One pull 9177-1026-P gives you a 5-1/16 inch (128 mm) center to center handle, polished chrome finish, and zinc construction in one cabinet pull. Its 7-25/32 inch length, 1-3/16 inch projection, and 15/32 inch width support comfortable gripping and clean lines across doors and drawers. For projects built around a 128 mm drilling pattern and polished chrome decorative hardware, this Advantage Series pull provides consistent dimensions you can repeat from one cabinet to the next.