Berenson Traditional Advantage Two Series 3" (76 mm) Center to Center Matte Black Pull, - 9186-1055-P

Berenson Traditional Advantage Two Pull For Cabinets

Berenson Traditional Advantage Two pull gives cabinets and drawers a consistent 3 inch center to center grip point, which helps installers line up drilling patterns across a run of doors and fronts. The pull uses a zinc material body, so it provides a solid feel while keeping weight manageable on standard cabinet faces. Its matte black finish adds a dark, non-reflective look that works well when a clean, understated style is needed on both residential and shop-built casework. With an overall length of 5-3/4 inches, this pull spans beyond the mounting holes, which provides visual balance across typical cabinet rail widths. A 7/8 inch projection sets the handle off the door far enough for fingers to wrap comfortably, supporting everyday opening and closing without knuckle rub on the surface.

Key Pull Details For Cabinet Projects

• The 3 inch center to center dimension defines the hole spacing, so installers can match this Berenson pull to existing 3 inch layouts or use standard drilling jigs without adjustment time.
• A length or diameter of 5-3/4 inches lets the pull visually cover a wider area on the face, which helps it look proportionate on many drawer sizes and narrow cabinet doors.
• The matte black finish tones down reflections, which keeps the pull looking consistent under varied shop, kitchen, or office lighting during daily use.
• A base diameter of 5/8 inch creates a defined footprint at each end, helping the pull sit firmly against the surface and giving a finished look around each mounting point.
• The 7/8 inch projection provides clearance between hand and door, which supports a secure grip even on deeper drawer fronts or thicker door profiles.

Mounting Dimensions That Support Clean Alignment

This Berenson Traditional Advantage Two pull uses a 3 inch center to center measurement, giving a fixed reference for drilling and layout on cabinet doors and drawers. Installers working from the 5-3/4 inch overall length can position the pull to align with rails and stiles, keeping hardware lines straight across banks of cabinets. The 5/8 inch base diameter at each end gives a defined landing area on the surface, so minor layout marks are covered once the pull is tightened down. With a 7/8 inch projection, the handle stands out enough that hands clear the face while still keeping the hardware close to the cabinet, which helps maintain a low-profile look across the installation.

Using This Matte Black Cabinet Pull In Work

Where This Advantage Series Cabinet Pull Fits

This pull belongs to the Advantage Series from Berenson Corporation, so it is suited for decorative hardware roles on cabinets and casework where a traditional style is specified. The zinc material construction supports use on typical residential or light commercial cabinetry, giving a sturdy feel on doors and drawers without adding unnecessary load to hinges or slides. Its matte black finish helps it coordinate with other dark cabinet components, so installers can keep a unified look across handles and matching hardware within a project. With a 3 inch center to center layout and 5-3/4 inch overall length, the pull works well on standard cabinet doors, utility cabinets, and many drawer widths that are built around common North American hardware spacing.

Why These Dimensions Help Repeatable Results

The fixed 3 inch center to center dimension lets shops and installers reuse existing jigs and drilling patterns, speeding up production runs or replacements that call for this spacing. The 5-3/4 inch length gives enough bar area between the 5/8 inch bases for a full four-finger grip, which matters when drawers are loaded or doors are taller and see frequent use. Because each base is 5/8 inch in diameter, the contact points distribute pressure around the screw locations, helping the pull seat neatly against the face once fastened. The 7/8 inch projection balances clearance with control, allowing users to pull from different angles without their fingers sliding off the matte black surface. As part of the Traditional Advantage Two design, these combined measurements help installers produce consistent, repeatable hardware layouts across multi-cabinet installations.

Common Questions About This Berenson Cabinet Pull

Select This Pull For 3 Inch Center Cabinets

The Berenson Traditional Advantage Two Series 3 inch center to center matte black pull ties together a zinc body, 5-3/4 inch length, and 7/8 inch projection to support everyday cabinet use. Its 5/8 inch base diameter at each end provides a clean transition from cabinet face to handle, which suits both new installations and updates built around 3 inch spacing. For projects calling for a traditional look in a matte black finish, this pull offers dimensions that align with common drilling patterns while maintaining comfortable hand clearance.