Sugatsune DSI-120 Series 7-9/16" (192 mm) Center to Center Satin Stainless Steel Pull, - DSI-120-192

DSI-120-192 Stainless Steel Pull For Cabinets

DSI-120-192 stainless steel pull is a Sugatsune DSI-120 Series handle designed as a 7-9/16 inch (192 mm) center to center pull, which sets consistent hole spacing for cabinet and furniture layouts. The pull is made by Sugatsune America, so it follows the DSI-120 Series geometry across projects that use this product line. The center to center length of 192 mm provides a longer grip span, which helps when aligning multiple doors and drawers in a straight visual line. The pull is classified as decorative hardware in the handles and pulls category, so it serves as both a working grip and a visible trim element on finished casework. The product is described as a handle and pull in the Sugatsune product class, which keeps it aligned with other functional cabinet hardware from the same source.

Key DSI-120-192 Pull Details For Projects

• The DSI 120 Series designation ties this pull to a defined Sugatsune product family, which helps keep style and proportions consistent when the same series is used across a room or job.
• The material listed as 304 stainless steel provides a solid metal construction, which supports a sturdy feel in daily use compared with lighter cabinet hardware materials.
• The satin finish on the stainless steel creates a muted surface, which reduces glare and helps fingerprints show less in busy kitchen or shop environments.
• The width of 1-3/16 inch sets the front face dimension of the pull, which gives installers a sense of how much visual presence the handle will have on narrower or wider fronts.
• The projection of 1-9/16 inch defines how far the pull stands off the door or drawer, which affects hand clearance and helps avoid knuckles hitting the surface during operation.

Installation Dimensions And Screw Interface

The DSI-120-192 pull uses a 192 mm center to center measurement, which directs exact drilling locations when laying out two mounting holes. This fixed spacing simplifies jig setup and repeat drilling across multiple fronts. The specified screw size of M4 x 25 mm describes a metric machine screw thread and length, which matches common cabinet drilling patterns built around through-bored fronts. The projection of 1-9/16 inch gives a predictable stand-off distance, so installers can coordinate clearance when doors open near adjacent hardware or trim. With a 1-3/16 inch width, the pull sits within a moderate footprint, which helps it land comfortably on standard cabinet rail heights.

Using This Sugatsune Handle In Real Work

Where The Sugatsune DSI-120 Series Pull Fits

The DSI-120-192 pull is identified as decorative hardware and a handle and pull, which positions it for use on cabinet doors, drawers, and similar casework fronts in woodworking projects. The 7-9/16 inch center to center length suits wider drawer faces or taller doors, where a longer pull helps balance the proportions of the front. Because the pull belongs to the DSI 120 Series, it can be paired with other sizes from the same line on multi-cabinet runs to keep a uniform look across upper and lower sections. The satin stainless steel finish provides a neutral metallic tone, which coordinates with a range of hinge finishes and appliance trims in kitchen, bath, and shop applications. The 304 stainless steel material supports use in woodworking environments where hardware may be touched frequently throughout the workday.

Details That Support Consistent Alignment And Feel

The 192 mm center to center dimension on the DSI-120-192 stainless steel pull creates a repeatable drilling pattern, which helps maintain straight handle lines across banks of doors and drawers. The M4 x 25 mm screw size matches a standard metric fastener length for through-bored fronts, which streamlines installation when fronts are prepared for machine screws. The 1-9/16 inch projection offers enough depth for a full finger grip, which contributes to a solid pull action on heavier drawers or loaded cabinets. With a 1-3/16 inch width, the pull presents a defined edge for the hand without overwhelming narrower rails, which can be important on smaller doors. The combination of 304 stainless steel material and satin finish yields a firm, smooth surface, which feels consistent from one pull to the next when multiple handles are installed in the same space.

Common Questions About The DSI-120-192 Pull

Select The DSI-120-192 Pull For Your Next Run

The DSI-120-192 stainless steel pull brings a 192 mm center to center layout, 1-3/16 inch width, and 1-9/16 inch projection together in a Sugatsune DSI 120 Series handle. With 304 stainless steel construction and a satin finish, it suits cabinet and furniture projects that call for a consistent, metal pull profile.