RD PULL 42MM C/C SATIN NICKEL identifies this Sugatsune RD Series tab pull as a compact, 42 mm center to center handle designed for cabinet and drawer use. The 1-5/8 inch (41 mm) center to center size creates a small footprint that fits tight layouts while still giving a defined gripping point. Its tab-pull form suits modern fronts where the handle wraps the edge, supporting clean lines on doors and drawers. The pull is made from a zinc alloy, so the body is metal rather than plastic, giving a solid feel when opening and closing. The satin nickel finish dresses the pull with a muted metallic look that coordinates with many contemporary hinges and fixtures. As part of Sugatsune America decorative hardware, this RD-55/SN pull fits into a coordinated RD collection for consistent styling across a project.
The 41 mm center to center measurement of this Sugatsune RD Series tab pull defines the distance between mounting points, which guides precise drilling on the cabinet or drawer front. Using the 42 mm center to center call-out in the SAP description alongside the 1-5/8 inch (41 mm) listing keeps metric and imperial planning aligned during layout. The compact span suits narrow rails or slim drawer faces, leaving margin from edges or panel joints. As a tab pull, the RD-55/SN is intended to sit at the edge of the door or drawer, so installers can reference that edge as a fixed datum when positioning the hole pattern for repeatable results on a run of fronts.
This Sugatsune RD Series 1-5/8 inch (41 mm) center to center tab pull is placed in the Handles and Pulls class within Decorative Hardware & Moldings, so it is set up for cabinet and furniture openings rather than general construction use. The compact 41 mm center to center span lets it land cleanly on smaller drawer fronts and doors where longer pulls would crowd neighboring fronts. Because it is part of the RD collection, the RD-55/SN model can be used in runs where a consistent profile is needed across multiple cabinets. The satin nickel finish gives a neutral metallic tone that matches many contemporary cabinet hinge finishes and other satin nickel decorative components in the same room.
The defined 1-5/8 inch (41 mm) center to center dimension on this satin nickel cabinet tab pull allows installers to transfer measurements directly from plans to workpieces, supporting consistent hole spacing along a bank of drawers. The SAP description calling out RD PULL 42MM C/C SATIN NICKEL confirms the 42 mm center to center intent, so metric jigs or drilling guides can be aligned to that span without conversion guesswork. The zinc alloy construction gives each pull a repeatable form, which helps edges and reveals line up visually when multiple pulls are installed side by side. As a tab pull, the RD-55/SN is intended to wrap or sit at the door or drawer edge, letting that edge act as the reference line for vertical positioning, which simplifies layout when repeating the install across many fronts.
The Sugatsune RD Series RD-55/SN tab pull has a 1-5/8 inch (41 mm) center to center dimension, giving a compact mounting span suited to smaller cabinet doors and drawers.
The RD-55/SN tab pull is categorized as decorative cabinet hardware in Handles and Pulls, so it is intended as the gripping point on doors and drawers in cabinetry or furniture.
The Sugatsune RD-55/SN pull is made from a zinc alloy, providing a metal body that delivers a solid feel and consistent appearance across multiple installations.
The RD-55/SN tab pull is finished in satin nickel, giving a muted metallic look that coordinates with other satin nickel cabinet hardware in the same project.
The RD-55/SN is part of the Sugatsune RD Series collection, allowing it to be used alongside other RD pulls to keep hardware style consistent across cabinetry.
The 42 mm center to center listing in the SAP description identifies the mounting hole spacing, helping align metric drilling jigs or layout guides for installation.
The Sugatsune RD Series RD-55/SN tab pull combines a 1-5/8 inch (41 mm) center to center span with a satin nickel finish and zinc alloy construction, giving a compact, metal pull suited to cabinet and drawer fronts. Its RD PULL 42MM C/C SATIN NICKEL designation ties directly to the mounting layout you plan in either metric or imperial. For projects calling for modern, edge-mounted hardware within the Sugatsune RD collection, this tab pull offers a defined size, material, and finish profile ready to drop into your cabinet hardware schedule.
Sold In: 1 Each