TMH pull 96mm c/c 24k gold plated describes a Sugatsune TMH Series brass pull that provides a 96 mm center-to-center mounting pattern, giving cabinet installers a standard spread that fits many layouts using this specific drill spacing. The 3-3/4 inch overall length pairs with the 96 mm center-to-center size to create a compact pull that works well on doors and drawers needing a smaller footprint while still offering a comfortable grip. The projection of 1-7/8 inch sets the working hand clearance off the front of the cabinet, helping users grab the pull without contact against the cabinet face, which supports smoother daily operation. The 11/16 inch width keeps the pull visually light across the rail or stile, helping it sit cleanly on narrow faces where wider pulls may crowd edges. The brass material forms the core structure of the pull, giving it a solid metal body that supports repeated use in cabinetry environments.
The 96 mm center-to-center measurement defines the distance between screw holes, guiding drilling templates and CNC programs for accurate mounting on cabinet faces. The M5 x 45 mm screw size specification pairs the pull with metric threaded fasteners that pass through typical door and drawer thicknesses, giving a defined thread and length reference during installation. The 1-7/8 inch projection tells installers how far the gripping surface stands off the front, which helps when checking door swing clearances near walls, adjacent cabinets, or tall trim. The 11/16 inch width provides a narrow band of contact along the rail or stile, supporting placements where wider pulls might interfere with panel profiles or tight edge reveals. The TMH Series identity links this pull to its matching base plate SLTMH-M35, which is available separately when a back plate detail is part of the design intent.
The Sugatsune TMH Series 3-3/4 inch pull with 96 mm center to center sizing fits cabinet doors and drawers that are laid out for this metric drilling pattern, aligning cleanly with a two-hole mount across the face. The brass construction helps the pull sit confidently on wood, laminate, or similar cabinet fronts by presenting a solid metal interface against the surface. The 24K gold plating on the body provides a high-visibility finish that integrates into cabinetry where gold-tone decorative hardware is specified. The black nickel ring detail supplies a darker contrast point, which assists designers building schemes that mix warm gold metal with cooler dark accents on the same assembly. The 1-7/8 inch projection supports comfortable gripping on standard-depth doors and drawer fronts by extending the pull outward for finger clearance. The 11/16 inch width allows positioning on narrow rails or stile edges where wider pulls could crowd door profiles or interfere with neighboring fronts.
The defined 96 mm center-to-center spacing on the TMH-96 pull lets installers repeat hole locations across multiple faces using the same metric layout, which supports efficient drilling with jigs or CNC programs tuned to this size. The specified M5 x 45 mm screw size tells fabricators the thread and length pairing expected at each mounting point, helping them match fasteners to common cabinet thicknesses without trial measurement. The combination of 3-3/4 inch length and 1-7/8 inch projection gives a predictable working envelope, which aids in checking for handle-to-handle clearances on pairs of doors or near adjacent walls. The brass body beneath the 24K gold plating provides a stable substrate for the finish, supporting consistent alignment when tightening the pull down against the door or drawer surface. The black nickel ring acts as a designed break in the finish, helping installers orient the pull consistently so the visual detail lines up across a run of cabinets.
The Sugatsune TMH-96 pull has a 96 mm center to center dimension, which sets the hole spacing installers use when drilling cabinet doors and drawers for this handle.
The TMH Series pull uses a brass body with 24K gold plating on the main body and a black nickel finish on the ring, giving a mixed-finish decorative appearance.
The Sugatsune TMH-96 pull projects 1-7/8 inch from the cabinet face, providing finger clearance for gripping doors and drawers during regular use.
The TMH Series pull specifies M5 x 45 mm screws, giving installers a defined metric thread and length reference for cabinet door and drawer mounting.
The TMH-96 pull has an overall length of 3-3/4 inch, a width of 11/16 inch, and a projection of 1-7/8 inch, defining its footprint and hand clearance on cabinets.
The TMH-96 pull lists the base plate SLTMH-M35 as available separately, giving designers a coordinated option when a back plate detail is desired.
The Sugatsune TMH Series TMH-96 pull brings a 96 mm center to center layout, M5 x 45 mm screw interface, and brass construction with 24K gold plating and a black nickel ring to cabinet projects. These defined dimensions and finishes support precise drilling, consistent mounting, and a mixed-finish decorative look across doors and drawers. When a 3-3/4 inch pull with this specific metric spacing and finish combination is required, this TMH-96 model from Wurth Baer Supply aligns with that specification.