DSI-4504 Recessed Pull Stainless Steel identifies this pull as a recessed unit designed to sit into the door face, which keeps the handle out of the way on sliding and pocket doors where clearance is tight. The web description states a modern, unobtrusive design, so the pull presents a clean look that suits contemporary furniture and door layouts. The same description lists a 1/16 inch, or 2 mm, projection, which means the pull stands off the surface very slightly, reducing snag points along the passage side. The SAP description specifies this as a sliding door pull at 6-1/8 inch length, giving enough gripping area for regular use while still fitting typical furniture and interior door proportions. Material options of 304 stainless steel or brass, noted in the web description, allow the pull to match metal choice across a project, from doors to surrounding decorative hardware.
The 1/16 inch (2 mm) projection stated in the web description keeps this recessed pull nearly flush to the door surface, which helps sliding or pocket doors travel into cavities without interference from protruding hardware. The SAP description defines this unit as a sliding door pull, so its recessed format supports applications where a standard surface-mounted handle would contact a frame or pocket edge. With an overall length of 6-1/8 inch, as specified in the SAP description, the pull spans more of the stile, giving a longer reach area that can be positioned at a comfortable height along the door.
The SAP description naming this part a sliding door pull positions it directly for doors that move laterally in furniture or openings. On cabinets or built-ins using bypass or single-track doors, the recessed format lets faces pass closely without hardware-to-hardware contact. The web description states the pull is ideal for furniture or pocket doors, so its geometry supports doors that disappear into a cavity or recess, where any extra projection would rub the pocket interior. The modern, unobtrusive design referenced in the web description suits casework where hardware should not dominate, allowing wood grain or panel design to remain the visual focus. Material choices of 304 stainless steel or brass, as stated, give flexibility when matching door pulls to existing hinges, knobs, or decorative edge trims in the same installation.
The modern, unobtrusive design reported in the web description means the pull keeps lines simple, which helps achieve consistent looks across multiple doors in a run. The 1/16 inch (2 mm) projection, also from the web description, limits stand-off across all installed pulls, supporting uniform clearance where several sliding leaves operate on shared tracks. The material specification of 304 stainless steel or brass provides two distinct base metals, so specifiers can standardize on one substrate while varying finish where needed. Finishes listed as satin, black, or antique brass allow a project to maintain one model number for geometry while using different surface appearances for separate rooms or furniture pieces.
The DSI-4504 sliding door pull is described in the SAP and web descriptions as a sliding door pull ideal for furniture or pocket doors, so it targets lateral-moving interior door and cabinet applications.
The web description lists a 1/16 inch (2 mm) projection, keeping the pull close to the door surface so pocket doors can travel into their cavities with minimal risk of the pull scraping the pocket sides.
The SAP description specifies a 6-1/8 inch length, providing a longer gripping area along the door edge that supports comfortable hand placement on furniture or interior sliding doors.
The web description lists 304 stainless steel or brass as material options, giving a choice between these two metals to align with project appearance or metal coordination requirements.
The web description specifies satin, black, or antique brass finishes, allowing the visible pull edge to coordinate with surrounding decorative hardware tones on cabinets or doors.
The web description notes a modern, unobtrusive design, which keeps the pull visually quiet so cabinet or door panel design remains prominent across banks of sliding fronts.
The SAP description identifies this part as the DSI-4504 sliding door pull at 6-1/8 inch length, so it serves projects needing a recessed grip along a moving door edge. The web description notes a 1/16 inch (2 mm) projection and modern, unobtrusive design, giving sliding or pocket doors a low-profile pull that stays close to the surface. With material options of 304 stainless steel or brass and finishes of satin, black, or antique brass, the pull offers coordinated visual choices for furniture and interior door runs.