Berenson Bravo Series 2-3/16" (56 mm) Center to Center Brushed Copper Tab Pull, - 1047-40BC-P

Berenson Bravo Tab Pull For Clean Cabinet Edges

Berenson Bravo tab pull gives you a compact aluminum cabinet pull in a brushed copper finish that mounts on 2-3/16 inch (56 mm) center to center spacing, so you get a precise fit on doors and drawers laid out to that drill pattern. The 3 inch overall length provides a small, controlled grip area that suits narrow fronts where larger pulls could crowd the layout. A projection of 1-3/4 inches extends the tab far enough off the face for easy finger access, helping users grab doors without raking knuckles along the front. The 3/4 inch width presents a slim profile that works well on lighter cabinet styles while still giving enough surface for a solid pull. With its brushed copper finish over aluminum, this pull delivers a warm metallic look on cabinetry while staying light in weight for straightforward handling during installation.

Key Bravo Edge Pull Details That Matter On Site

• The 2-3/16 inch (56 mm) center to center dimension sets the hole spacing, simplifying layout when you are drilling for consistent runs of doors and drawers on a project.
• The 3 inch length or diameter measurement describes the overall span of the pull, helping you balance scale on smaller cabinet fronts and avoid overcrowding tight face frames.
• The 1-3/4 inch projection defines how far the pull stands off the surface, giving enough clearance for fingers while reducing the chance of snagging in high-traffic areas.
• The 3/4 inch width provides a narrow front profile, which helps when you want a minimal look that does not visually dominate flat-panel or slab cabinet designs.
• The 11/16 inch base diameter sets the footprint at the contact point, which guides how much flat surface you need for stable mounting on the door or drawer front.
• The brushed copper finish specifies the color and sheen, letting you coordinate this pull with other brushed copper decorative hardware and trim in the same space.

Mounting Details For Accurate Bravo Edge Pull Alignment

This Bravo edge pull uses 2-3/16 inch (56 mm) center to center mounting, so the two mounting points align to standard dual-hole drilling on many cabinet layouts. The specified screw size of 8-32 x 1 inch establishes the thread and reach through typical cabinet fronts, giving a straightforward fastening method familiar to cabinet installers. With an 11/16 inch base diameter, the pull sits on a compact contact area, so it seats cleanly on flat surfaces without overhanging narrow rails. The 1-3/4 inch projection and 3/4 inch width work together to position the gripping edge away from the door face, which supports consistent clearance when doors meet tight reveals or adjacent panels.

Using The 1047-40BC-P Pull In Cabinet Projects

Where This Brushed Copper Tab Pull Works Best

The Berenson Bravo Series 1047-40BC-P tab pull, with its 2-3/16 inch (56 mm) center to center dimension, suits cabinet doors and drawers that are already drilled or planned to that spacing, which keeps replacement or new installations straightforward. Its 3 inch overall length fits well on small to medium fronts, so you can keep proportions controlled on narrow drawers where larger pulls might look oversized. The brushed copper finish supports use in spaces that call for warm metallic tones, allowing you to tie cabinet faces into other brushed copper decorative hardware and moldings. Aluminum construction keeps the pull light, which is helpful when you are hanging multiple pulls across a large run of cabinets and want predictable handling during fitting. The 1-3/4 inch projection gives the hand a defined edge to grab, which can make everyday opening smoother on heavier doors.

Why Bravo Edge Pull Dimensions Support Consistent Results

The defined 2-3/16 inch (56 mm) center to center spacing on this Bravo edge pull lets you repeat drilling patterns confidently across multiple cabinets, which helps maintain straight visual lines along doors and drawer banks. A 3/4 inch width keeps the pull slim, so it sits neatly near door edges without crowding adjoining fronts, which is useful on modern slab installations with tight gaps. The 11/16 inch base diameter focuses the pull load onto a compact area, encouraging solid contact with the cabinet face for steady operation over time. With a 3 inch length, this pull gives enough span for a full fingertip grip, which can improve user comfort on frequently used doors. The 1-3/4 inch projection places that gripping edge away from the surface, supporting consistent clearance when doors swing past adjacent cabinets or appliances, which contributes to smoother day-to-day use.

Common Questions About The Bravo Edge Pull 56mm

Select This Bravo Pull For Precise Cabinet Layouts

The Berenson Bravo Series 2-3/16 inch (56 mm) center to center brushed copper tab pull brings together aluminum construction, a 3 inch length, and 1-3/4 inch projection to support accurate drilling and comfortable everyday use. With a 3/4 inch width and 11/16 inch base diameter, it suits tighter cabinet layouts where controlled scale matters. For projects calling for brushed copper decorative hardware, this 1047-40BC-P pull provides a consistent size and look across doors and drawers, helping you finish the run with predictable results.