Berenson Bravo Series 6-5/8" (169 mm) Center to Center Brushed Copper Tab Pull, - 1049-40BC-P

Bravo Edge Pull 169mm Brushed Copper Use

Bravo edge pull 169mm brushed copper describes a Berenson Bravo Series tab pull designed as a low-profile handle solution for cabinet fronts and similar casework. The pull uses a 6-5/8 inch (169 mm) center to center drilling, so it matches layouts patterned around this common span and keeps hole placement consistent across doors and drawers. The overall 6 inch length creates a clean, compact line on the edge of the panel, helping runs stay visually aligned on banks of cabinets. A 1-3/4 inch projection pulls the gripping point off the face enough for fingers to catch comfortably, which helps on heavier or full-overlay doors. The 3/4 inch width keeps the pull slim at the front edge, allowing it to sit neatly at door tops or drawer edges without crowding adjacent fronts or nearby hardware.

Key Bravo Edge Pull Details For Projects

• The Berenson Bravo Series identity ties this pull into a defined hardware collection, so matching other Bravo handles on the same job is straightforward when coordinating a consistent style.
• The aluminum material keeps the tab pull light, which reduces unnecessary load on door faces or drawer fronts and supports smooth action for typical cabinet hardware setups.
• The brushed copper finish brings a warm metallic tone with a subtle texture, helping the pull sit well against a range of woodgrains or painted finishes on cabinetry.
• The 6 inch length paired with a 6-5/8 inch center to center layout creates a narrow margin at each end, producing a modern tab look that lines up well on contemporary cabinet designs.
• The 1-3/4 inch projection provides a defined hand space away from the cabinet face, which supports easier gripping when opening taller pantry doors or wide drawer fronts.
• The 3/4 inch width keeps the visible front edge minimal, which helps maintain clean sightlines on slab fronts and reduces visual clutter on multi-drawer stacks.

Mounting Dimensions And Fit For This Pull

This Bravo edge pull uses a 6-5/8 inch (169 mm) center to center dimension, so hole drilling patterns can follow a single measurement across the run for repeat installations. The 6 inch overall length means the body of the pull slightly under-runs the hole spread, leaving the mounting area focused at the ends, which suits tight layouts where fronts sit close together. A base height of 11/16 inch defines how far the tab portion stands up at the mounting edge, which helps align the pull consistently near door or drawer tops. The 1-3/4 inch projection adds working clearance between the hand and the cabinet face, reducing contact with finished surfaces during daily use. With a 3/4 inch width, the pull occupies a restrained band on the edge so it can be positioned on narrow drawer rails or thin door frames while staying inside the available face area.

Using The Berenson Bravo Pull In Cabinet Work

Where This Brushed Copper Tab Pull Fits Best

The Berenson Bravo Series 6-5/8 inch (169 mm) center to center tab pull fits cabinet and furniture fronts that are drilled on the 169 mm pattern, so it suits metric-based layouts or conversions that follow this spacing. Its 6 inch overall length keeps it proportionate on standard-width doors and drawers, allowing multiple pulls along a run without dominating the front. The brushed copper finish presents a muted metallic surface that complements many stains and paint colors, which is useful when tying new hardware into existing casework. With a base height of 11/16 inch, the pull sits up just enough at the edge to be easy to grab while remaining low against the panel, an advantage on frameless cabinet designs where fronts need a slim, integrated handle. The 3/4 inch width also supports placing the pull close to corners without overhanging neighboring fronts.

Details That Support Repeatable Cabinet Results

The defined 6-5/8 inch (169 mm) center to center spacing on the Bravo edge pull supports consistent drilling templates, which helps keep handle lines straight across doors and drawer banks from project to project. The 1-3/4 inch projection is fixed, so once the pull is mounted, every opening point along a run offers the same finger clearance, contributing to a uniform feel across the installation. Aluminum construction gives the pull a stable shape while keeping mass low, which works well on overlay doors where added weight at the edge can affect hinge action. The 6 inch length used together with the 3/4 inch width creates a compact footprint that repeats cleanly, providing a predictable visual pattern on horizontal or vertical layouts. The combination of brushed copper finish and tab form factor allows installers and fabricators to pair the same part with different cabinet styles while maintaining the same drilling and mounting approach.

Common Questions About This Bravo Edge Pull

Selecting This Edge Pull For Cabinet Runs

The Berenson Bravo edge pull 169mm brushed copper provides a defined 6-5/8 inch center to center dimension, a 6 inch length, and a 1-3/4 inch projection, giving installers a repeatable tab pull pattern across cabinet runs. With aluminum construction, a 3/4 inch width, and a brushed copper finish, it delivers a slim, consistent gripping point that lines up well on doors and drawers when planning hardware for new builds or refresh work.