PRO LUXE Bistro Series pull identifies this handle as part of the Bistro collection, which ties multiple pulls together visually across a project. The material being zinc gives you a metal pull that handles normal cabinet use while keeping weight manageable during installation. The black nickel finish delivers a dark metallic look that coordinates with other black nickel hardware runs. The 3 inch center to center dimension sets the hole spacing, so it directly matches drilling layouts based on that standard size. The overall length of 3-7/8 inch keeps the pull compact on smaller doors or drawer fronts while still spanning the 3 inch centers cleanly. A projection of 1-1/16 inch creates hand clearance in front of the cabinet face, which helps fingers grab the pull without scraping knuckles. The 11/16 inch width presents a slim profile that fits well on narrow rails or modern flat fronts.
The 3 inch center to center value is the primary mounting dimension, because it defines where to bore the two fastener holes on each cabinet front. The specified length of 3-7/8 inch shows how far the pull stretches across the surface, which helps when aligning it with panel proportions or neighboring hardware. The projection of 1-1/16 inch indicates how far the front edge of the pull stands off the door or drawer, which affects both clearance and how far the hand reaches. The 11/16 inch width reflects how much rail or flat area the pull will occupy, guiding placement on narrow face frames or slab fronts. The screw size of 8-32 x 1 inch matches a common machine screw standard, which aligns with typical cabinet door and drawer front thicknesses used by many shops.
The Bistro collection name and Belwith product class place this pull firmly in decorative handles and pulls, so it suits cabinet doors and drawer fronts that call for a finished look. The 3 inch center to center spacing aligns with a widely used cabinet drilling standard, which helps when laying out hardware on both new builds and refurb projects designed around that spacing. The 3-7/8 inch length keeps the pull proportional on standard kitchen and bath fronts where a compact handle is preferred. The 1-1/16 inch projection works on doors that swing past adjacent panels, because the grip stands off the face enough for fingers to wrap around without relying on oversized backset. The 11/16 inch width makes this pull a good match for narrow rails or smaller drawers, where a wider bar might crowd moldings or neighboring pulls.
The defined 3 inch center to center dimension allows jigs and templates built for that spacing to be used repeatedly, which supports consistent alignment across banks of doors. The 3-7/8 inch overall length leaves a small margin past each screw hole, so the ends of the pull sit close to the fastener locations and reduce the chance of visible misalignment. The 1-1/16 inch projection positions the grip at a predictable distance from the cabinet face, which helps installers maintain the same reach feel across different sections of a room. The 11/16 inch width keeps the contact area narrow, which simplifies aligning the pull with stile edges, panel reveals, or layout lines on slimmer components. The use of zinc for the body and black nickel for the finish combines a sturdy substrate with a defined surface treatment, which keeps the visual result repeatable from piece to piece within the same collection.
The PRO LUXE Bistro Series pull has a 3 inch center to center measurement, which sets the drilling distance between mounting holes on cabinet doors or drawer fronts.
The PRO LUXE SZ13BLN pull is 3-7/8 inch long, so it slightly overhangs the 3 inch screw spacing to give a balanced look on standard cabinet fronts.
This black nickel cabinet pull has a projection of 1-1/16 inch, providing finger clearance between the pull and the cabinet surface during everyday use.
The Bistro Series cabinet hardware pull is 11/16 inch wide, so it fits comfortably on narrow rails or drawer fronts without overwhelming the face.
The PRO LUXE Bistro Series pull is made from zinc, giving it a metal construction suited to typical cabinet door and drawer applications.
This Belwith cabinet pull uses 8-32 x 1 inch screws, matching a common machine screw standard used for many cabinet doors and drawer fronts.
The PRO LUXE Bistro Series 3 inch center to center black nickel pull combines a zinc body, Bistro collection styling, and Belwith decorative hardware classification to support coordinated cabinet projects. The defined dimensions - 3-7/8 inch length, 1-1/16 inch projection, and 11/16 inch width - streamline layout on doors and drawers built around 3 inch centers. The black nickel finish ties into modern and transitional designs where a dark metallic accent is needed. For cabinet runs that call for consistent drilling and a compact, matching handle across multiple fronts, this PRO LUXE Bistro Series pull provides a clear, dimensioned choice.
Sold In: 1 Each