10 x 10 x 3 classic overhang bar bracket corbel cherry describes a Pro Value Series wood corbel sized for substantial bar or counter overhangs, giving installers a defined footprint to work with on layout-heavy projects. The 10 inch height and 10 inch projection set a clear support zone under tops, so spacing and load paths can be planned consistently along a run. The 3 inch width keeps the corbel visually solid while staying practical for mounting against standard cabinet or wall framing. Being identified as a classic overhang bar bracket corbel signals a decorative profile suited to traditional bar, island, or counter designs where exposed support is part of the look. The cherry material allows this corbel to visually tie into cherry cabinetry or tops, keeping the support element aligned with the overall millwork design.
The 10 inch height and 10 inch projection on this Pro Value Series cherry corbel give installers clear geometry for mounting under counters or bar tops, which simplifies aligning the back face with cabinet rails or wall studs. Its 3 inch width offers a stable bearing surface against the supporting structure, so the corbel can sit flush along face frames or blocking once the installer has set their fastener pattern. Because it is made of unfinished wood, any field trimming or fine-tuning of the back edge can be done before finishing, reducing visible adjustments after installation. The classic overhang bar bracket identity also signals that this piece is intended to sit proud under an overhang, so installers can coordinate edge reveals and decorative profiles around its fixed 10 by 10 by 3 inch envelope.
This Pro Value Series 10 x 10 x 3 classic overhang bar bracket corbel cherry is suited to bar, island, and counter applications where a visible support element is part of the design. The 10 inch projection works under deeper overhangs found on bar tops, giving a meaningful presence beneath the surface. Its 10 inch height lets the corbel bridge from the underside of the top down toward the cabinet or wall face, tying the top visually back to the structure. With a 3 inch width, the corbel sits proportionally against standard cabinet modules while remaining substantial enough to read as a primary support element along the run. The cherry wood body pairs naturally with cherry casework and trim, helping installers maintain a continuous material story from base cabinets through decorative moldings and supports in one coordinated line.
The unfinished wood construction on this classic cherry corbel means shops can control every finishing step, from sanding through stain and topcoat, so finished pieces match existing cherry tones or custom color systems across a job. That same unfinished surface simplifies blending out any minor shaping or fitting at the back edge before finishing, which keeps the presentation faces clean once the corbel is in place. The defined 10 inch by 10 inch by 3 inch sizing supports repeatable layout: once an installer has dialed in spacing and setbacks for one project, the same measurements carry forward to future work using this part. The Pro Value Series branding and the specific SZDW11160CH manufacturer part number give purchasing and project teams a clear identifier for ordering and documentation, which helps maintain consistency when multiple trades or phases rely on the same cherry corbel specification.
The corbel is identified as 10 inches by 10 inches by 3 inches, giving installers a clear projection, height, and width to plan spacing, support zones, and alignment under counters or bar tops.
The Pro Value Series SZDW11160CH corbel is made of cherry wood, allowing it to visually coordinate with cherry cabinetry, tops, and decorative moldings in bar or counter installations.
The corbel is made of unfinished wood, so shops and installers can sand and finish it to match existing cherry millwork or custom color requirements on a specific project.
This classic overhang bar bracket corbel is suited for bar, island, and counter runs where a visible cherry wood support ties the countertop visually back to the cabinets or wall structure.
The 10 x 10 x 3 size provides a predictable mounting footprint and projection, which simplifies layout, alignment, and repeat spacing when running multiple corbels along cabinets or walls.
The SZDW11160CH manufacturer part number uniquely identifies this cherry corbel, supporting clear ordering, documentation, and future reorders for matching installations.
This 10 x 10 x 3 classic overhang bar bracket corbel cherry from the Pro Value Series gives you a defined cherry wood support for visible bar and counter runs. With an unfinished cherry body, you can align stain and sheen to existing millwork while using the 10 inch by 10 inch by 3 inch geometry as a consistent layout reference across projects. Referencing the SZDW11160CH part number keeps purchasing, shop, and field teams aligned on the exact corbel used whenever a bar or counter design calls for a classic cherry support element.