Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
3/4 inch edge grip kit from the Pro Value Series uses 3/4 inch diameter edge grips to hold artwork, photos, or glass by the edge rather than drilling through the material, which keeps the face surface intact during mounting. The kit uses satin clear anodized aluminum edge grips, so the hardware presents a neutral, finished appearance around the mounted piece in typical workspace or display settings. Each edge grip in this SZG4028 kit is 1 inch long, providing a compact mounting point that supports the panel edge without taking up much visual space around the display. This system is designed to work with material up to 1/4 inch thick, so installers can size panels knowing the grip range is set for common photo, artwork, or glass thicknesses. The assembly is rated for material weighing up to 20 pounds, which defines the practical load range for each mounted display.
The SZG4028 3/4 inch diameter x 1 inch long edge grip kit is built around a clamp-style hold on the panel edge, so the mounting process centers on aligning the material thickness within the grip range up to 1/4 inch. Because the grips are 1 inch long, there is enough contact length to stabilize the panel edge while still giving flexibility in where grips are placed along the perimeter. The satin clear anodized aluminum finish helps the grips sit visually in the background of a finished installation, so attention stays on the artwork, photo, or glass. With a working capacity of up to 20 pounds, installers can plan wall or display layouts for pieces that fall within that weight while using the same part number SZG4028 across similar jobs.
This Pro Value Series standoff kit is described as an edge grip solution for installing photos, artwork, or glass, so it fits naturally into wall displays, presentation walls, or branded graphics where drilling through the material is not desired. Because the system accommodates material up to 1/4 inch thick, it aligns with many standard substrates used for framed-style displays or glass panels in that thickness range. The 3/4 inch diameter footprint on each grip keeps the mounting points modest in size, which helps when arranging multiple pieces closely on a wall. Its 20 pound capacity supports medium-weight displays, so installers can use it across recurring projects that require a defined weight limit. The satin clear anodized aluminum finish suits commercial interiors or office environments where a clean, understated hardware look is preferred around the display material.
The combination of a 3/4 inch diameter and 1 inch length on each edge grip creates a consistent geometry, which helps installers repeat hole locations and edge clearances from job to job using the same SZG4028 part. The stated 1/4 inch maximum material thickness gives a clear boundary for panel selection, so cutting, finishing, and ordering of photo, artwork, or glass pieces can be standardized around that dimension. The 20 pound weight rating gives a defined performance target, allowing planning of display sizes that stay within the intended load capability for each mounted piece. Because the grips rely on an edge hold rather than a through-hole, panels stay intact, which simplifies reusing or updating artwork while retaining the existing wall layout. The satin clear anodized aluminum finish gives a consistent visual across multiple installations, so repeated projects using this Pro Value Series standoff kit maintain the same look throughout a space.
The SZG4028 edge grip kit accommodates material up to 1/4 inch thick, so panels or glass within that range seat properly in the grip opening during installation.
This Pro Value Series edge grip setup is rated for material weighing up to 20 pounds, which defines the load range when planning display size and substrate choice.
Each edge grip in the SZG4028 kit is 3/4 inch in diameter and 1 inch long, giving a compact mounting footprint that still offers usable contact length on the panel edge.
The edge grips use a satin clear anodized aluminum finish, providing a neutral metallic look that suits many display environments and keeps attention on the mounted piece.
This edge grip kit is described for installing photos, artwork, or glass, so it suits wall displays or presentation areas using those materials within the 1/4 inch thickness range.
The manufacturer part number is SZG4028, which identifies this specific 3/4 inch diameter by 1 inch long satin clear anodized edge grip kit.
The SZG4028 3/4 inch diameter x 1 inch long edge grip kit in satin clear anodized aluminum ties together defined panel thickness, weight capacity, and compact dimensions for photo, artwork, or glass displays. For projects built around material up to 1/4 inch thick and up to 20 pounds, this Pro Value Series standoff kit provides a repeatable option rooted in these stated parameters. Use this part when a clean, edge-held presentation and consistent geometry across multiple installations are important to the finished result.
