Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Edge grip kit from the Pro Value Series provides a simple way to mount photos, artwork, or glass without drilling through the material, so the piece stays intact while still being held securely at the edge. The 1 inch diameter grip presents a compact support point that stays discreet around smaller signs and panels, helping projects look clean and controlled. Each edge grip is 1-1/4 inch long, giving enough bearing surface along the panel edge for stable clamping on typical display sizes. As a standoff-class component, this design holds material slightly off the mounting surface, which helps visual pieces stand out while staying firmly located. The satin clear anodized finish treats the aluminum body, giving it a uniform, muted metallic look that works well in many multimedia and workspace layouts where glare needs to stay low.
This Pro Value Series standoff-style edge grip is built around a 1 inch diameter body and 1-1/4 inch length, so each point of support occupies a modest footprint while projecting enough to clamp onto the panel edge. The hardware is designed to hold material from 1/8 inch to 1/2 inch thick, which covers many photo mounts and glass panes used in display work. With a weight capacity of up to 20 pounds, the system supports typical small to medium display pieces within that load. Phillips head screws are used to draw the grip body tight, turning screwdriver torque directly into clamping force, which helps seat panels firmly. The multi-purpose nylon wall anchors provide a receptacle in the wall structure, helping the assembly bite into substrates that would not reliably hold a screw alone.
The SZG4029 edge grip kit, classified under standoffs, is intended for mounting photos, artwork, or glass panels by holding them at the edge, so it fits well anywhere a clean, drilled-free face is desired. Its 1 inch diameter body stays relatively compact around visual pieces, helping the hardware read as a neat point detail instead of a bulky bracket. With the ability to handle material from 1/8 inch to 1/2 inch thick, one set can serve across a mix of substrates such as thin photo boards, medium acrylic panels, and thicker glass. The up to 20 pound capacity suits many interior wall-mounted displays in workspaces, multimedia areas, or closets, where individual panels fall within that weight. Satin clear anodized aluminum provides a neutral metallic tone that blends with many wall finishes while coordinating with other anodized components.
Holding panels without drilling through them preserves the integrity of artwork or glass, which matters when working with tempered glass or prints that could be compromised by holes. The 1-1/4 inch long aluminum body gives the grip enough length to engage a solid portion of the edge, promoting consistent clamping pressure along the supported side. Managing material between 1/8 inch and 1/2 inch thick reduces the need to switch hardware as project requirements change, helping maintain a unified appearance across a wall. The 20 pound working range provides a clear boundary for design, letting you size panels and layout spacing around a known capacity. Using Phillips head screws means installers can drive and snug the system with widely available screwdrivers or bits, which keeps site setups straightforward. Nylon wall anchors help the assembly bear loads in a variety of wall constructions by spreading stress through the anchor body rather than concentrating it only on screw threads in softer materials.
The edge grip kit handles material from 1/8 inch up to 1/2 inch thick, allowing it to clamp securely on many common photo boards, acrylic sheets, and glass panels within that thickness range.
The SZG4029 edge grip kit is rated for material weighing up to 20 pounds, so it suits small to medium wall-mounted displays that stay within that stated load limit per application.
The edge grips hold panels by the edge without drilling into the material, which keeps artwork and glass intact and helps avoid weakening or damaging sensitive pieces during mounting.
Each Pro Value Series edge grip is 1 inch in diameter and 1-1/4 inch long, providing a compact, standoff-style support that still offers sufficient length for effective edge clamping.
This aluminum edge grip kit has a satin clear anodized finish, giving a muted metallic appearance that coordinates well with many interior surfaces and other anodized components.
The edge grips mount using Phillips head screws driven into multi-purpose nylon wall anchors, so the load transfers through the anchor into the wall substrate for secure support.
The Pro Value Series 1 inch diameter x 1-1/4 inch long edge grip kit in satin clear anodized aluminum provides a standoff-style way to hold panels from 1/8 inch to 1/2 inch thick and up to 20 pounds. When a project calls for mounting photos, artwork, or glass without drilling into the material, this SZG4029 kit supplies a defined thickness range, a stated weight capacity, and a compact footprint that suits many wall displays. Choose this edge grip kit when those verified dimensions, load ratings, and finish match the requirements of your installation layout.
