Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Basic Series steel wire pull 5 c c gives cabinets and furniture a straightforward handle that suits everyday shop work. The pull uses zinc material, so it offers a solid metal grip that feels consistent from piece to piece in a run. The finish is polished chrome, which creates a bright, clean look that aligns with typical modern cabinet fronts in kitchens, baths, or shop-built casework. The pull length of 5-5/16 inches provides finger space across wider drawer fronts, which helps when opening loaded drawers. A projection of 1-1/4 inches sets the grip away from the face, giving clearance for fingers without overhanging too far into walk paths. The 5/16 inch width keeps the profile slim, which works well on narrow rails and small doors where a bulkier pull could crowd the layout.
The 5 inch center to center dimension defines the mounting hole layout, which allows jigs to be set once for repeatable drilling across all doors and drawers on a project. With a 1-1/4 inch projection, the pull sits off the face enough to clear typical door bevels and drawer front edges when installed on standard thickness fronts. The 5-5/16 inch total length covers the span between the holes, which helps visually center the pull on common drawer rail sizes used in many cabinet runs. A 5/16 inch width keeps the footprint narrow, allowing the pull to fit on slim stiles where space between edge and panel is limited.
This Pro Value Series wire pull belongs to the PRO Basics collection, which positions it for routine cabinet and furniture work where a simple bar shape fits the design. The 5 inch center to center measurement lines up well with many cabinet layouts that standardize on 96 to 128 millimeter ranges, giving a consistent spacing feel across doors and drawers. The polished chrome finish coordinates with other polished chrome decorative hardware and moldings in the same space, tying together hinges, latches, or trim that share the bright metal look. Because the pull measures 5-5/16 inches in length, it suits medium drawer fronts commonly found in base cabinets, vanities, and shop storage units. The combination of zinc material and wire form keeps the handle visually lean, which works where a low-profile look is preferred over bulkier block pulls.
The manufacturer part number 81139 67 028 identifies this specific 5 inch center to center wire pull, which simplifies reordering when a shop wants identical hardware for future runs or replacements. The defined 1-1/4 inch projection allows designers to plan clearances relative to adjacent doors, drawer faces, and wall surfaces, promoting uniform ergonomics from one cabinet bank to the next. With a 5/16 inch width, the pull aligns nicely on narrow rails without overlapping into panel areas, which keeps drilling locations predictable for door and drawer construction. The polished chrome finish maintains a consistent appearance across a full job, which matters when multiple faces line up in banks and any variation would stand out. The Basic Series steel wire pull geometry also helps maintain the same hand feel across every opening point, so users experience a uniform grip when operating doors and drawers along a full elevation.
The Basic Series steel wire pull has a 5 inch center to center dimension, which sets the hole spacing for consistent drilling across cabinet doors and drawers.
The Pro Value Series wire pull measures 5-5/16 inches in overall length, which covers the span between the mounting points and suits many medium drawer fronts.
The wire pull has a 1-1/4 inch projection, creating finger clearance between the grip and the cabinet face for comfortable opening of doors and drawers.
This cabinet pull uses zinc material with a polished chrome finish, giving a metal base with a bright surface that coordinates with other polished chrome hardware.
The Basic Series wire pull has a 5/16 inch width, which keeps the bar slim so it fits well on narrow rails and smaller cabinet fronts.
The manufacturer part number is 81139 67 028, which identifies this specific 5 inch center to center polished chrome wire pull for ordering or matching.
The Basic Series steel wire pull 5 c c from the PRO Basics collection uses a 5 inch center to center layout, zinc construction, and a polished chrome finish to support unified cabinet hardware runs. Matching part number 81139 67 028 across doors and drawers keeps spacing, appearance, and hand feel consistent throughout the project.
Sold In: 1 Each