Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Multipurpose Project Blocks from Kreg Tool raise your workpiece 1-1/2 inches above the bench, so sanding, finishing, routing, and other operations have room for tools and clearance for edges. This elevation keeps material off the bench surface, which helps keep abrasive dust, wet finish, or chips away from the work area under the board. Each block is part of a set of 4, so you can support a project at four corners for stable work support on sawhorses, benches, or temporary setups. As woodworking hand tools and equipment, these blocks fit easily into a regular workflow where pieces need to move from sanding to routing to assembly. The Kreg Tool KFS-PUCK part number identifies these as project-ready supports designed for repeat use in the shop or on site.
The Kreg Multipurpose Project Blocks are designed as standalone supports, so putting them into service is simply a matter of placing the set of 4 under your workpiece with the Grip Maxx surface oriented for the task. When sanding or routing, setting the Grip Maxx side that contacts the bench downward helps the blocks stay planted, while the opposite Grip Maxx face grips the workpiece so it resists movement. The 1-1/2 inch working height is consistent across all four blocks, which keeps the work level as long as the underlying surface is reasonably flat. For finishing work, twisting the block to raise the retractable painting point provides a higher, point-contact support. This raised point lets wet finishes rest on minimal contact areas, which matters when you need all coated faces to remain clean.
The Kreg Tool KFS-PUCK Multipurpose Project Blocks fit into sanding workflows where material must stay steady while you push an orbital sander, sanding block, or hand tool across a panel. Elevating stock 1-1/2 inches lets dust escape off the edge instead of building against a bench stop directly under the work. During routing, these blocks create clearance for the router bit and base at the edge, so decorative profiles or flush trimming can run the full perimeter without contacting the support below. In drilling and assembly work, the same elevation gives clamp heads space to sit under the workpiece, which supports pocket-hole drilling or joint assembly where clamping pressure comes from underneath. As a set of 4, the blocks can be spaced to support corners or key bearing points on frames, shelves, doors, or panels.
The Grip Maxx surface on each face of the Kreg Multipurpose Project Blocks plays two roles in day-to-day use: it helps lock the block to the workstation and grips the workpiece resting on top. This dual grip reduces sliding during sanding or routing, which supports more consistent passes and reduces the need to reposition parts. The retractable painting point with Grip Maxx adds another layer of workflow efficiency, because the same block used for sanding and routing can transition directly to finishing. Twisting the block to raise the painting point converts the support from a broad pad to a point-contact rest, so freshly painted or finished surfaces have minimal touch points. Since the painting points do not stick to the material or ruin the finish, a part can be coated, set back on the blocks, and left to dry without disturbing the surface. By combining elevation, anti-slip faces, and retractable points in one design, these project blocks move with a project from prep through assembly and finishing.
Kreg Multipurpose Project Blocks elevate material 1-1/2 inches above the work surface, which provides clearance for sanding, finishing, routing, and clamping under the workpiece during drilling or assembly.
The Grip Maxx surface on each face grips both the workpiece and the workstation, which reduces slipping when you sand so you can focus on even pressure instead of holding the board in place.
The retractable painting point with Grip Maxx provides a little extra height and point-contact support, so finished pieces rest on small points that do not stick or damage the finish as it dries.
The 1-1/2 inch elevation created by the project blocks gives router bits and bases clearance under the edge, which lets you route profiles without cutting into your bench or support surface.
The block height provides room for clamp heads under the workpiece, which supports pocket-hole drilling or assembly setups where clamping pressure is applied from below the material.
The Kreg Multipurpose Project Blocks use manufacturer part number KFS-PUCK, which identifies this specific set of project support blocks in the Kreg Tools product class.
The Kreg Multipurpose Project Blocks KFS-PUCK set brings 1-1/2 inch elevation, Grip Maxx surfaces, and retractable painting points into a single solution that supports sanding, routing, drilling, assembly, and finishing. This combination lets the same set handle prep work, edge machining, and final coating without changing support methods. For shops and serious DIY users working with panels, frames, or small assemblies, these Kreg Tools project blocks provide consistent height and traction that translates directly into smoother passes and more stable setups. Add this set of 4 to your workflow when steady support, clearance for tools, and finish-friendly contact points are priorities.
Sold In: 1 Set