Amerock Urbanite Series 7-9/16 in (192 mm) Center to Center Matte Black/Matte Black Pull, -BP778192MBMB

Amerock Urbanite Pull For Cabinet Projects

Amerock Urbanite pull 192mm center to center describes a cabinet pull from the Amerock Urbanite Collection that uses a 7-9/16 in center-to-center mounting, so it matches layouts drilled to this common size on doors and drawers. The pull is identified as Manufacturer Part # BP778192MBMB, which ties it to a specific Amerock Urbanite Series part for repeat ordering and project consistency. The material is listed as Zinc/Aluminum, giving a metal construction that supports typical cabinet use in woodworking environments. The finish is Matte Black / Matte Black, so both the primary surfaces present the same low-sheen black appearance for a uniform look across a run of cabinets. The pull length is specified as 10-1/4 in, creating a longer handgrip span that suits wider fronts where more reach and visual presence are needed.

Key Amerock Urbanite Details For Cabinet Work

• The 7-9/16 in (192 mm) center-to-center dimension aligns with a standard drilling pattern, which streamlines layout when setting up new fronts or matching pre-bored cabinet doors and drawers.
• The 10-1/4 in overall length creates a pull that visually anchors taller doors and wider drawer faces, helping maintain proportion across bases, walls, and pantry cabinets in a run.
• The 1-3/16 in projection defines how far the pull stands off the surface, providing functional finger clearance while keeping the handle close enough to the face for a clean, low-profile line.
• The 1/2 in width gives a slim front profile, which supports a contemporary, linear style while still presenting enough surface for a comfortable grasp at typical cabinet positions.
• The base dimensions of 7/16 in long by 1/2 in wide localize the contact area at each end, which can help align the pull on narrow rails or stile edges during installation.

Mounting And Fit Dimensions For This Pull

The center-to-center measurement of 7-9/16 in establishes the hole spacing for this Amerock Urbanite pull, so alignment depends on drilling or existing bores matching this 192 mm spread. The projection is 1-3/16 in, which defines how much stand-off there is between the cabinet face and the gripping surface, supporting comfortable access at typical door and drawer positions. The pull width of 1/2 in sets the front face dimension, tying into slim, modern cabinet lines while still giving a defined edge to pull against. Base dimensions listed as 7/16 in length by 1/2 in width describe each mounting foot contact area on the door or drawer front, which matters when positioning on narrow framing or slab fronts.

Using The Amerock Urbanite Pull In Cabinet Layouts

Where This Urbanite Pull Works In Cabinets

This Amerock Urbanite Series pull is categorized under Handles and Pulls in Decorative Hardware & Moldings, placing it in typical cabinet and furniture hardware applications for woodworking projects. The 7-9/16 in (192 mm) center-to-center size supports use across base cabinets, wall units, and larger drawer fronts that are drilled on this spacing, creating continuity through a kitchen or casework job. The 10-1/4 in overall length allows this pull to span more of the front surface on wide drawers or tall doors, which can help tie together banked drawers and pantry fronts visually. A Matte Black / Matte Black finish lets the pull read as a dark, continuous bar on the face, which works well against light cabinet finishes or coordinated dark surfaces in built-ins.

Dimensions That Support Consistent Results

The defined 7-9/16 in center-to-center dimension means existing 192 mm layouts can accept this pull without changing drilling, which matters on refacing work or replacing hardware on pre-bored fronts. Projection of 1-3/16 in sets a predictable hand clearance from the cabinet surface, which can reduce variation between doors and drawers when this model is used throughout a project. The 1/2 in face width gives an installer a consistent visual band to align parallel to door and drawer edges, helping maintain straight sightlines along rows of cabinets. Base dimensions of 7/16 in by 1/2 in help determine how much flat mounting area is needed at each foot, which is useful when placing pulls close to edge details or on narrow frames. The Zinc/Aluminum material construction provides a metal pull body that matches typical expectations for decorative cabinet hardware used in woodworking environments.

Common Questions About This Amerock Urbanite Pull

Select This Urbanite Pull For 192 Mm Layouts

The Amerock Urbanite Series 7-9/16 in (192 mm) center-to-center Matte Black / Matte Black pull gives a defined set of dimensions for cabinet layouts that use this spread. With a 10-1/4 in length, 1-3/16 in projection, and 1/2 in width, it fits projects calling for a longer linear handle. The Zinc/Aluminum material and Matte Black / Matte Black finish align this pull with metal decorative hardware choices suited to woodworking industry cabinet and furniture work.