Amerock Transcendent Series 5/8 in (16 mm) Center to Center Matte Gold Pull, -BP741416MGMG
Description
Amerock Transcendent Matte Gold Pull For Cabinets
Amerock Transcendent matte gold pull gives you a compact cabinet handle with a 5/8 in (16 mm) center-to-center layout, so it suits tight drawer or door rail spacing where standard pulls do not fit. The aluminum construction provides a light, rigid pull that handles frequent daily use without adding extra weight to smaller fronts. Its matte gold finish delivers a muted metal look that coordinates with other matte gold decorative hardware on the same run. At 3-3/16 in overall length, this pull spans a short distance on the face, which helps on narrow drawer fronts while still offering enough grip area. A 1-3/16 in projection stands the pull off the surface, allowing fingers to get behind it without interference from the door or drawer face.
Key Amerock Transcendent Pull Details In Use
- The 5/8 in (16 mm) center-to-center dimension sets the mounting hole spacing, which matters when laying out drilling patterns on new cabinetry or matching an existing short-span layout in a retrofit job.
- The 3-3/16 in overall length keeps the pull compact on narrow doors and drawer fronts, which helps maintain balanced proportions on small cabinet faces while still providing a practical grip span.
- The 1-3/16 in projection establishes how far the pull stands off the surface, which affects finger clearance behind the handle and helps reduce knuckle contact against the cabinet face when opening.
- The 3/8 in width defines the front profile of the pull, which affects how it feels in the hand and how prominently it reads on the cabinet face in a line of matching handles.
- The 1 in by 1 in base dimensions create a square footprint at each contact point, which spreads bearing on the door or drawer face and sets a consistent visual block at both ends of the pull.
- The 8-32 screw size sets the threaded interface in the pull, which aligns with common cabinet hardware drilling and helps streamline installation across multiple fronts on the same project.
Mounting And Layout Details For This Pull
The 5/8 in (16 mm) center-to-center measurement defines the exact distance between mounting points, so drilling can be laid out accurately on jigs or templates before installation. With a 3-3/16 in total length, the pull fits comfortably on smaller doors while keeping end clearances predictable around stile and rail joinery. The 1-3/16 in projection fixes how far the pulling surface stands proud of the cabinet, which helps when planning clearances near adjacent doors, walls, or trim. A 3/8 in width establishes a narrow gripping surface that feels precise on compact fronts without crowding the face. The 1 in by 1 in base dimensions set square contact pads, aiding in consistent alignment along cabinet runs.
How This Amerock Pull Works On Cabinets
Where The 5/8 In Center Pull Fits Best
The 5/8 in (16 mm) center-to-center layout suits cabinet doors or drawers that cannot accept full-size pulls, because it concentrates mounting within a short span while still presenting a defined handle. On narrow drawer fronts, the 3-3/16 in overall length keeps the pull from overreaching edges, which is helpful around tight banks of drawers. The 1 in by 1 in base dimensions create compact square pads at each end, giving a clear visual stop on slim stiles. With a 3/8 in width, the pull presents a slim front profile that works visually on small fronts where heavier pulls might dominate. The matte gold finish coordinates with other matte gold decorative hardware, which supports consistent appearance across a full kitchen or shop build using the same finish family.
Details That Support Repeatable Cabinet Results
The defined 5/8 in (16 mm) center-to-center spacing allows installers to use fixed jigs or drill guides, which helps repeat hole placement quickly across multiple doors. The 3-3/16 in overall length gives a fixed reference when aligning pulls at consistent offsets from door edges, supporting straight visual lines across upper and lower cabinets. A 1-3/16 in projection keeps the grip area consistent from face to face, which helps doors and drawers open with a similar feel throughout a run. The 3/8 in width keeps finger contact focused, which can aid users who prefer a narrower pull on small drawer fronts. The 1 in by 1 in base dimensions establish predictable square landing points against the surface, which helps the pull register consistently when tightening from the back side. The aluminum material provides a rigid body for the threaded 8-32 interface, supporting secure mounting once fastened into place.
Common Questions About This Matte Gold Pull
What is the mounting hole spacing on this pull?
The Amerock Transcendent matte gold pull has a 5/8 in (16 mm) center-to-center spacing, which sets the distance between mounting holes for drilling and layout on cabinet doors or drawers.
How long is the Amerock Transcendent matte gold pull?
The pull length is 3-3/16 in, which keeps it compact on narrow cabinet fronts while still offering enough bar length for a comfortable hand grip in daily use.
What is the projection of this cabinet pull from the door?
The projection is 1-3/16 in from the cabinet face, which provides finger clearance behind the pull and helps prevent knuckles from brushing the door or drawer front.
What material and finish does this Amerock pull use?
The pull is made from aluminum with a matte gold finish, giving a light metal body and a subdued gold appearance that pairs with other matte gold decorative hardware.
What are the base dimensions on the cabinet surface?
Each base measures 1 in long by 1 in wide, creating square contact pads that define the pull footprint and support consistent visual alignment on cabinet faces.
What screw thread size does this pull accept?
The pull uses 8-32 screws, which matches a common cabinet hardware thread pattern and supports straightforward fastening through standard drilled cabinet holes.
Choose This Pull For Compact Gold Cabinet Runs
The Amerock Transcendent matte gold pull with 5/8 in (16 mm) center-to-center spacing offers a short mounting pattern that fits compact doors and drawers. Its 3-3/16 in overall length and 1-3/16 in projection create a usable grip on smaller fronts. The aluminum material and matte gold finish tie into Amerock decorative hardware lines, which supports consistent appearance across a project. For jobs calling for a small-footprint gold handle, this pull provides defined dimensions that support repeatable cabinet layouts.