Amerock Transcendent pull 192mm center to center gives cabinets a consistent hand feel across doors and drawers because the 7-9/16 in center-to-center dimension keeps screw spacing standardized on the run. The polished nickel finish presents a bright metallic surface that reads clean on modern or transitional fronts, helping hardware lines stay visually sharp. Aluminum construction keeps each pull light, so larger fronts experience less added weight during everyday use. The 10-11/16 in overall length provides a long gripping area that works well on taller doors where users naturally grab higher or lower along the handle. A 1-3/16 in projection sets the pull off the face enough for fingers to wrap behind without rubbing the panel. The 3/8 in width keeps the profile slim so doors can open near adjacent walls or appliances with minimal clearance conflict.
The 7-9/16 in center-to-center measurement on this Amerock Transcendent pull lines up with a standard 192 mm drilling pattern, so installers can bore consistent rows using metric or imperial layout references. Base dimensions of 1 in by 1 in at each end give a defined landing area on the face, which helps cover the immediate area around the screw holes. The 1-3/16 in projection fixes the stand-off depth from the door, so users get predictable clearance for fingers behind the pull. The specified 8-32 x 1 in screw size ties directly to common cabinet door and drawer construction, letting the threaded connection match a widely used hardware standard.
This Amerock Transcendent Series pull with 7-9/16 in center-to-center spacing fits cabinet layouts designed around a 192 mm drilling grid, which is common on many modular kitchen and bath runs. The 10-11/16 in overall length suits wider doors and drawers where a longer handle looks proportionate to the front size. With a 3/8 in width, the pull presents a slim line across face frames or frameless fronts, helping multi-door sections look aligned rather than bulky. The 1 in by 1 in base dimensions at each footing deliver square contact points on the panel, giving a defined footprint for positioning along stiles or rails. Aluminum construction keeps each pull relatively light on large pantry doors, so the feel at the hinge side stays closer to the original door weight.
The 7-9/16 in center-to-center dimension supports repeatable drilling because installers can set jigs or templates for a single 192 mm pattern and run it across doors and drawers. The 1-3/16 in projection establishes a fixed offset that helps doors open without fingers sliding against painted or laminated faces, which matters on frequently used kitchen fronts. With the 3/8 in width, the pull allows doors near corners to swing without a wide handle edge overhanging into tight reveals. Polished nickel finish keeps the surface visually crisp against many cabinet colors, so alignment errors are easier to spot and correct as hardware is laid out along a run. The 1 in square base at each end provides a clear visual reference when centering on rails, helping pulls sit level from door to door within a bank of cabinets.
The Amerock Transcendent pull uses a 7-9/16 in (192 mm) center-to-center measurement, so hole spacing follows a 192 mm pattern for consistent cabinet boring.
The BP7414192PNPN Transcendent pull has a 10-11/16 in overall length, giving a long gripping area that works well on wider cabinet doors and drawers.
This polished nickel pull projects 1-3/16 in from the cabinet face, providing space for fingers to wrap behind the handle during normal opening and closing.
The Amerock Transcendent cabinet pull is made from aluminum, keeping weight modest while still giving a solid metallic feel in daily cabinet use.
Each base on this pull measures 1 in long by 1 in wide, creating a square footprint that defines the pull contact area on the cabinet front.
This Amerock cabinet pull is specified for 8-32 x 1 in screws, aligning with a common cabinet hardware thread size for doors and drawers.
This Amerock Transcendent Series 7-9/16 in (192 mm) center-to-center polished nickel pull ties hardware layout directly to a clear drilling standard, which supports efficient cabinet runs. The 10-11/16 in overall length, 1-3/16 in projection, and 3/8 in width combine into a handle that feels comfortable to grab while staying visually lean across multiple fronts. With aluminum construction and 1 in by 1 in base dimensions, the BP7414192PNPN model aligns appearance, weight, and mounting footprint for straightforward cabinet hardware planning.