Amerock Transcendent Series 12-5/8 in (320 mm) Center to Center Silver Champagne Pull, -BP7414320SCSC

Amerock Transcendent Pull 320mm For Cabinet Projects

Amerock Transcendent pull 320mm is a 12-5/8 in center to center cabinet handle that spans 15-3/4 in overall length, giving wide hand clearance across larger doors or drawers. The handle uses a 320 mm center-to-center layout, so it aligns with long-run drilling patterns on wider fronts. Its 1-3/16 in projection sets the grip off the face enough for comfortable access while keeping the handle close to the surface for a clean line. The pull uses a 3/8 in width profile that keeps the look slim while still presenting a defined edge to grab. With base dimensions of 1 in by 1 in at each mounting point, it spreads contact on the surface, which supports stable mounting on typical cabinet materials. The Amerock BP7414320SCSC part number identifies this exact Transcendent Series pull in Silver Champagne finish for repeat ordering.

Key Amerock Transcendent Series Handle Details

• The pull belongs to the Amerock Transcendent Collection, so its design lines coordinate with other Transcendent pieces, which supports consistent styling across doors and drawers in the same project.
• The handle is made from aluminum, so it provides a rigid metal construction while keeping weight down on the door or drawer front, which supports smooth hardware operation over typical cabinet cycles.
• The Silver Champagne finish presents a light metallic appearance that works with many door colors, and the consistent finish across the pull helps create a uniform look on banks of fronts.
• The center-to-center dimension is 12-5/8 in (320 mm), so it fits long drilling spans used on wider drawers, which helps set pulls at a comfortable reach across large faces.
• The pull length of 15-3/4 in extends past the mounting points, giving extra gripping area toward both ends, which helps users grab the handle from different approach angles.
• The projection of 1-3/16 in holds the gripping surface off the cabinet face, giving finger clearance behind the pull while keeping it tight enough to reduce snag points in narrow walkways.
• The 3/8 in width keeps the bar slim, so it sits visually light on modern fronts while still presenting enough surface area for a steady hand grip in regular use.
• The 1 in by 1 in base dimensions at each mounting point provide a defined footprint, which helps the pull sit square against the surface for a neat installed appearance.

Cabinet Pull Fit, Dimensions, And Mounting Layout

This Amerock Corporation pull is specified with a 12-5/8 in (320 mm) center-to-center dimension, so it fits layouts drilled to that span on cabinet doors or drawers. The 15-3/4 in overall length means the bar extends beyond the mounting holes, so users gain a longer gripping section than the drill pattern alone. With a projection of 1-3/16 in, the handle stands off the face enough for typical hand clearance without pushing the grip too far into the room. The 3/8 in width and 1 in by 1 in base dimensions define the footprint on the front, which helps installers understand how the pull will visually balance on narrow rails or wide slab fronts when positioned along the edge or centered.

Using This Amerock Transcendent Pull In Projects

Where This 12-5/8 Inch Drawer Pull Fits Best

The Amerock Transcendent Series 12-5/8 in center to center pull works well on wide cabinet drawers or tall doors where a longer handle improves reach. The 320 mm center-to-center dimension supports use on larger fronts that benefit from a long gripping point, giving users leverage across the span. Its 15-3/4 in overall length allows the pull to visually anchor broader faces, which helps balance the proportions on base cabinets or pantry doors. With a 3/8 in width and 1-3/16 in projection, the pull presents a slim, extended profile that pairs with contemporary cabinet lines while still offering practical hand access. The 1 in by 1 in base dimensions at both ends provide a clear mounting footprint that suits face-frame or frameless cabinet fronts where a defined mounting pad looks intentional.

Why These Dimensions Support Repeatable Installation Results

The defined 12-5/8 in (320 mm) center-to-center dimension gives installers a fixed drilling reference, so hole placement can be repeated across multiple cabinets using the same layout. The 15-3/4 in length means that once holes are laid out for 320 mm centers, the handle overhang is predictable on each side, which keeps the visual reveal consistent. A projection of 1-3/16 in creates reliable finger clearance behind the bar, so users can grip from below or the side without crowding the door surface. The 3/8 in width keeps the handle narrow enough that it does not dominate narrow rails, while still giving a firm edge to pull against during daily use. With 1 in by 1 in base dimensions, the contact area around each mounting point is clearly sized, which helps align the pull square to door edges and drawer lines when working across banks of cabinets.

Common Questions About This Amerock Cabinet Pull

Select This Pull For 320mm Cabinet Installations

The Amerock Transcendent pull 320mm center to center in Silver Champagne offers a defined 12-5/8 in drilling span, a 15-3/4 in overall length, and a 1-3/16 in projection that together support comfortable use on larger cabinet fronts. Aluminum construction with 3/8 in width and 1 in by 1 in bases provides a slim, modern profile with a clearly sized mounting footprint. For projects built around 320 mm spacing and a Silver Champagne finish, this Amerock BP7414320SCSC handle gives a consistent, repeatable option across doors and drawers.