Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Amerock Concentric pull 96mm identifies this handle as part of Amerock's Concentric Series, which standardizes style and sizing for cabinet and drawer layouts. The pull is described as a handle in the Decorative Hardware & Moldings category, so it is intended for visible cabinet and furniture fronts where appearance and grip both matter. The center-to-center dimension is 3-3/4 in (96 mm), providing a common drill pattern that supports straightforward handle alignment across multiple doors and drawers in a run. Overall length is 4-3/16 in, which leaves some material beyond the screw holes for a finished look at each end. The pull has a projection of 7/8 in from the mounting surface, giving finger clearance for opening doors and drawers without needing an exaggerated reach. A width of 1 in and base dimensions of 5/16 in long by 1 in wide define the footprint on the face, which helps cover the drilled hole area while keeping a streamlined profile.
The BP36812G10 Amerock pull uses a 3-3/4 in (96 mm) center-to-center mounting layout, so the handle fastens through two drilled holes on that spacing, which aligns with many cabinet boring jigs and templates. The specified screw size is 8-32 x 1 in, indicating the pull is tapped for standard 8-32 machine thread, which matches common cabinet hardware screw assortments. Base dimensions of 5/16 in long by 1 in wide define the bearing surface against the door or drawer front, helping spread load slightly while covering the bore area along the width. With 7/8 in projection, the handle stands off just under an inch from the front, providing working clearance for fingers without creating a deep obstruction near cabinet faces. The 1 in overall width gives a stable gripping surface while staying narrow enough for smaller drawer fronts and doors.
The Amerock Concentric Series 3-3/4 in (96 mm) center-to-center satin nickel pull is positioned for use on cabinet doors and drawers, as indicated by its category as Handles and Pulls within Decorative Hardware & Moldings. The satin nickel finish supports use in kitchens, baths, and built-ins where a subdued metallic tone coordinates with other satin nickel decorative hardware. A 3-3/4 in (96 mm) center-to-center size matches a widely used mounting pattern, so this pull suits new casework layouts that follow common boring dimensions. Its 4-3/16 in overall length works on standard cabinet door stiles and medium-width drawer fronts, providing enough bar length without dominating narrow faces. The zinc material supports everyday gripping and repeated use in typical residential and light commercial cabinets where a metal pull is desired on frequently used doors and drawers.
The Amerock Concentric pull 96mm center-to-center measurement aligns with standard 96 mm drilling, so once the first set of holes is located, the same jig setting can be used across the run for consistent handle placement. The 8-32 x 1 in screw size gives a defined thread and length expectation when preparing for attachment through standard door and drawer thicknesses, helping streamline hardware planning. A projection of 7/8 in establishes a predictable stand-off from the surface, which helps installers anticipate clearance around adjacent doors, drawer faces, and nearby trim. The 1 in width and 5/16 in by 1 in base dimensions create a known footprint, which aids in positioning relative to door edges and stile widths when aligning multiple pulls. Being part of the Amerock Concentric Series ties the pull into a named collection, supporting repeat use on additional projects that call for the same visual and dimensional pattern.
The Amerock Concentric Series pull uses a 3-3/4 in (96 mm) center-to-center dimension, which sets the hole spacing for mounting on cabinet doors and drawers.
The BP36812G10 pull has an overall length of 4-3/16 in, a projection of 7/8 in from the surface, and a width of 1 in, defining its grip reach and visual size.
The cabinet handle is made from zinc with a satin nickel finish, giving a metal construction with a subdued metallic appearance for decorative cabinet installations.
This Amerock Concentric Series handle is specified for 8-32 x 1 in screws, so its threaded holes are sized for standard 8-32 machine-thread cabinet fasteners.
The satin nickel pull has a projection of 7/8 in from the mounting surface, providing finger clearance while keeping the handle relatively close to the cabinet face.
The Amerock Concentric Series designation ties this pull to the Concentric collection, aligning its style and basic proportions with other items in that series.
The Amerock Concentric Series 3-3/4 in (96 mm) center-to-center satin nickel pull pairs a standard 96 mm drilling pattern with a 4-3/16 in overall length, supporting consistent layouts on cabinet doors and drawers. Its zinc construction and 7/8 in projection provide a defined grip profile that suits everyday cabinet use. With a satin nickel finish coordinated to decorative hardware applications, this pull aligns with common project specifications. For cabinets and furniture that call for a 3-3/4 in (96 mm) center-to-center handle from the Amerock Concentric Series, this BP36812G10 pull offers a defined size, finish, and mounting layout for repeatable results.