Amerock Concentric cabinet pull is a zinc handle designed for cabinet and furniture applications where consistent alignment matters. The 5-1/16 in (128 mm) center-to-center mounting spreads the load across two fastener points, which helps the pull feel solid in daily use on doors or drawers. The overall length of 5-7/16 in gives fingers a clear grabbing area, which supports a comfortable pull motion on wider drawer fronts. A projection of 7/8 in holds the grip away from the face frame, which reduces knuckle contact when opening heavier fronts. The 1 in width provides a stable hand contact patch, contributing to controlled opening and closing. Satin nickel finish presents a neutral metallic look that works alongside many hinge and appliance finishes in the same space. Base dimensions of 5/16 in long by 1 in wide define the footprint that bears on the cabinet surface.
The 5-1/16 in (128 mm) center-to-center dimension establishes the hole spacing pattern, which allows installers to mark and drill repeatable locations across multiple fronts. The 5-7/16 in overall length then defines the visible span of the Amerock pull over that pattern, which helps position it in relation to panel rails and stiles. A 7/8 in projection determines how far the pull stands off the surface, which keeps fingers clear of raised panel details while opening doors. The 1 in width and 5/16 in by 1 in base dimensions describe the bearing area on the cabinet face, which supports stable seating against the finished surface. The use of 8-32 x 1 in screws defines the thread size and length engaged through typical cabinet fronts.
This Amerock Concentric Series pull belongs to the handles and pulls category, which aligns it with doors and drawers on cabinets and furniture. The satin nickel finish lets the BP36813G10 coordinate visually with satin nickel hinges or appliance handles in the same room, supporting a unified hardware look. With a 5-1/16 in (128 mm) center-to-center size, the pull fits layouts that call for a mid-size handle across kitchen, bath, or storage runs using that drilling pattern. The 5-7/16 in overall length works well on standard drawer widths, because it spans enough of the front to look balanced without crowding adjacent hardware lines or trim details.
The zinc material of the Amerock Concentric Series pull creates a solid body that holds its shape when tightened against the cabinet face, which supports consistent alignment from one door or drawer to the next. A projection of 7/8 in controls stand-off from the surface, which keeps hand clearance similar on every opening where this pull is used. The 1 in width and 5/16 in by 1 in base dimensions give installers predictable bearing points, which helps set the pull square to door edges and stile lines during installation. The specified 8-32 x 1 in screw size defines the fastener thread and reach through typical cabinet fronts, which supports reliable fastening practice across a run of cabinets using the same pull.
The Amerock Concentric cabinet pull has a 5-1/16 in (128 mm) center-to-center dimension, which sets the drilling pattern for mounting on cabinet doors or drawers.
The BP36813G10 pull measures 5-7/16 in in overall length, which provides a visible span that suits many standard cabinet drawer and door widths.
This satin nickel pull has a 7/8 in projection, which positions the gripping surface away from the cabinet face to support finger clearance when opening fronts.
The Amerock Concentric Series pull is made from zinc, which provides a rigid body for a secure feel when installed on cabinet doors or drawers.
This cabinet pull uses 8-32 x 1 in screws, which defines the thread size and length that fasten the pull through standard cabinet fronts.
The base of the Amerock Concentric pull measures 5/16 in long by 1 in wide, which sets the footprint resting on the cabinet surface at each mounting point.
The Amerock Concentric cabinet pull in satin nickel pairs a 5-1/16 in (128 mm) center-to-center layout with a 5-7/16 in overall length, which aligns well with common cabinet drilling patterns and proportions. Zinc construction and a 7/8 in projection support a solid feel and consistent hand clearance across doors and drawers. For projects built around satin nickel decorative hardware and mid-size pulls, the BP36813G10 offers a defined set of dimensions that can be repeated across a full run.