Amerock Concentric pull is a zinc cabinet handle designed for decorative hardware work where consistent sizing helps layout. The pull is part of Amerock's Concentric collection, so it ties into that specific design family on a project. Its polished nickel finish provides a bright metallic look that coordinates with other polished nickel decorative hardware in kitchens, baths, and built-ins. The center-to-center dimension is 10-1/16 in (256 mm), which controls hole spacing and helps align with drilling jigs or existing 256 mm layouts on longer cabinet doors and drawers. Overall length is 10-7/16 in, so the ends extend slightly beyond the drilling centers for visual balance on wider fronts. The projection is 7/8 in from the mounting surface, providing finger clearance while keeping the profile tight to the face. A 1 in width offers a slim front view that works well on modern and transitional cabinet runs.
This Amerock Concentric Series pull uses a 10-1/16 in (256 mm) center-to-center mounting pattern, which sets the drilling points for installation and ties directly into 256 mm cabinet hardware layouts. The manufacturer lists the screw size as 8-32 x 1 in, defining the thread and length for the fasteners that engage the pull's internal threads. That sizing allows the installer to match the threaded fastener to standard 8-32 cabinet door and drawer mounting practices. The base dimensions are 5/16 in long by 1 in wide at each foot, which defines the footprint that sits against the cabinet surface and matters when laying out the pull on narrow stiles, rails, or face-frame edges. With a 7/8 in projection, the pull stands off the surface a defined amount, giving consistent depth across all doors and drawers on the run.
This Amerock Concentric Series pull is specified as a handle and pull in the decorative hardware and moldings category, so it is intended for cabinet doors and drawers in woodworking projects. The 10-1/16 in (256 mm) center-to-center layout makes it a fit for designs that call for longer pulls across wide drawer fronts or tall doors where a longer grip point is desirable. Its polished nickel finish positions it for projects that coordinate with polished nickel faucets, hinges, and other Amerock cabinet hardware elements. The 1 in width allows it to sit on standard cabinet rails without overhang, which is useful on framed and frameless cabinet systems that keep rail heights modest. Zinc construction means the pull is a metal component rather than a composite or wood piece, suitable for decorative hardware roles in residential and commercial millwork environments.
The defined 10-1/16 in (256 mm) center-to-center dimension gives installers a precise drilling distance, which supports consistent alignment when repeating the same pull across a full kitchen or bank of casework. Its 10-7/16 in overall length makes layout straightforward when centering the pull on drawer fronts, because the installer can reference both the center-to-center holes and the visible bar length for proportion. A projection of 7/8 in controls how far the handle stands out, which helps keep door swing clearances predictable around adjacent walls or panels. The specified 8-32 x 1 in screw size identifies the thread pattern used to secure the pull, so it ties directly into typical cabinet fastener practice and lets the installer align pull thickness with common door and drawer front thicknesses. Base dimensions of 5/16 in long by 1 in wide define the contact patch against the surface, which helps with positioning on narrow rails and keeps the pull seated flat when properly tightened.
The Amerock Concentric pull has a 10-1/16 in (256 mm) center-to-center dimension, so drilling for installation follows that exact spacing on cabinet doors and drawers.
The pull length is 10-7/16 in overall, so it extends slightly beyond the 256 mm mounting holes for a balanced look on wider fronts.
The Amerock Concentric pull projects 7/8 in from the cabinet surface, giving finger clearance behind the bar while keeping a relatively low profile on doors and drawers.
The Amerock Concentric pull is made from zinc with a polished nickel finish, so it provides a metal feel and coordinates with other polished nickel decorative hardware.
Each base on this pull measures 5/16 in long by 1 in wide, which defines the footprint resting on the cabinet surface during installation.
The Amerock BP36816PN pull is specified with an 8-32 x 1 in screw size, matching common cabinet fastening threads for mounting pulls on doors and drawers.
This Amerock Concentric Series 10-1/16 in (256 mm) center-to-center polished nickel pull brings defined metrics to cabinet hardware planning. The 256 mm hole spacing, 10-7/16 in overall length, 7/8 in projection, and 1 in width together set clear expectations for layout on doors and drawers. Zinc construction with a polished nickel finish establishes both material and visual pairing with other Amerock cabinet hardware pieces on the same job. For projects calling for a longer, polished nickel handle in the Amerock Concentric collection, this BP36816PN pull provides the specific dimensions needed to align drilling patterns and appearance across the run.