Amerock Kamari pull 96mm identifies this as Amerock Corporation part BP36822PN, so installers get a consistent profile across projects using this series. The pull is part of the Kamari collection, giving cabinets a unified look wherever matching Kamari hardware is used. Its material is zinc, which keeps the pull solid while remaining workable for standard cabinet door and drawer applications. The finish is polished nickel, creating a bright, reflective surface that coordinates with other polished nickel components on the job. With a length of 4-15/16 inches, the pull spans enough surface area for a full hand grip on doors and drawers. A 1 inch projection sets the hand clearance off the front, helping fingers wrap behind the pull without contacting the cabinet face during operation.
The 3-3/4 inch (96 mm) center-to-center spacing on the Kamari pull lines up with a widely used drilling pattern, helping new installations match common jig setups. Its overall 4-15/16 inch length lets the ends slightly overhang the boring spread, which visually anchors the pull while following standard layout rules. With a 1-3/16 inch width, the pull covers the fastener area effectively, helping the hardware sit proportionally on typical cabinet rails and drawer fronts. The 1 inch projection holds the gripping surface slightly off the face, which helps doors and drawers operate without knuckles rubbing the surface during repeated use.
The Kamari pull belongs to Amerock Corporation and sits in the handles and pulls class, so it is suited to cabinet and drawer projects needing decorative hardware. Its 3-3/4 inch (96 mm) center-to-center drilling dimension matches many cabinet layouts, making it practical when new fronts are bored to a standard pattern. The 4-15/16 inch overall length works well on typical kitchen and bath doors, providing balanced coverage without overpowering narrower rails. With a 1-3/16 inch width, the pull presents enough face to read visually on both doors and drawers, which helps maintain a consistent look across a run of cabinetry. The polished nickel finish coordinates with other polished nickel components, aligning knob and pull choices on the same job for a unified appearance. The zinc construction keeps the pull in the decorative hardware category used on wood cabinetry and similar casework.
The 96 mm center-to-center bore dimension on the Amerock Kamari cabinet pull helps installers repeat drilling patterns quickly across multiple fronts. Using the 3-3/4 inch spacing with standard jigs keeps hole locations consistent, which speeds layout on larger kitchens or banks of drawers. The base size of 3/8 inch by 3/8 inch concentrates each mounting point, so alignment is defined by the screw locations and the pull sits square when the bores are accurate. With its 1 inch projection, the pull stands off the surface enough that installers can visually confirm straightness along a cabinet run by sighting down the grips. The overall 4-15/16 inch length gives clear reference between adjacent pulls, which helps maintain even spacing from door edges when following a repeatable layout. The polished nickel finish presents a smooth, uniform surface that visually highlights any misalignment, encouraging precise placement during installation.
The Amerock Kamari BP36822PN pull has 3-3/4 inch (96 mm) center-to-center holes, matching a common drilling pattern for cabinet doors and drawers.
The Amerock BP36822PN Kamari pull is 4-15/16 inches in overall length, giving a full hand grip span on typical cabinet doors and drawers.
The Amerock Kamari BP36822PN pull is made from zinc, placing it in the decorative cabinet hardware range used on standard wood casework.
The Kamari polished nickel pull projects 1 inch from the cabinet face, providing finger clearance while keeping a relatively low profile.
The Amerock Kamari BP36822PN pull is 1-3/16 inches wide, covering the mounting area and presenting a clear visual line on doors and drawers.
Each mounting base on the Kamari pull measures 3/8 inch long by 3/8 inch wide, defining a compact footprint at every screw location.
The Amerock Kamari cabinet pull offers 3-3/4 inch (96 mm) center-to-center spacing, 4-15/16 inch overall length, and 1 inch projection, so it aligns with common cabinet drilling patterns. Its zinc construction and polished nickel finish match decorative hardware needs on coordinated cabinet projects.