Amerock Kamari 128mm matte black pull is a zinc cabinet handle designed with a 5-1/16 inch center-to-center mounting span, so it bridges standard drill patterns for many cabinet and drawer layouts and keeps hole boring straightforward on repeat jobs. The matte black finish creates a low-glare look that helps fingerprints read less on working kitchen and shop fronts. The pull body uses zinc material, giving a solid metal feel that suits everyday cabinet and drawer use. Overall length is 6-3/16 inches, giving enough hand clearance across wider drawer fronts without looking oversized on smaller doors. A 1 inch projection sets the handle off the face enough for a firm grip while staying tight to the cabinet line. The 1-3/16 inch width presents a broad front profile that reads cleanly across multiple doors in a run.
The Kamari pull uses a 5-1/16 inch center-to-center measurement, so installers can mark and drill two mounting points at that span for consistent alignment across doors and drawers. Its 6-3/16 inch overall length helps cover existing 5-1/16 inch hole spreads if upgrading from older hardware using the same boring. With a 1 inch projection, the pull stands off just enough from the cabinet face to allow fingers behind the bar while staying close for a clean, streamlined look on face frames or slab fronts. The 1-3/16 inch width gives a substantial front surface, which helps the pull look balanced on both narrow doors and wider drawers in a shared design.
This Amerock Kamari Series zinc pull in matte black is sized for cabinets or drawers laid out on a 5-1/16 inch center-to-center pattern, which is common on many residential and light commercial casework runs. The 6-3/16 inch length allows the pull to visually span mid-size drawer fronts while still working comfortably on standard upper cabinet doors, supporting a single style across the entire layout. With 1 inch of projection, the handle provides usable finger clearance on thicker doors without projecting far into working aisles, which is useful on galley kitchens or tight built-in areas. The 1-3/16 inch width keeps the pull proportioned on both small and large fronts, helping maintain a consistent look when repeating this model across different cabinet sizes.
The defined 5-1/16 inch center-to-center dimension on the Kamari pull makes it straightforward to repeat drilling and jig setups across a job, supporting quick production work with minimal layout changes between cabinets. Its 6-3/16 inch overall length means when a door or drawer is already bored on a 5-1/16 inch pattern, this pull covers the span cleanly without misalignment or overhang past the hole layout. The 1 inch projection keeps the gripping surface at a predictable stand-off from the face, which helps doors and drawers open with the same feel across the entire run. A 1-3/16 inch wide front face also gives installers a visually stable reference when aligning handles by sightline, which is helpful when setting hardware level across multiple cabinet rows. The matte black finish ties these dimensions together into a single, consistent visual line, so repeating this pull supports uniform appearance from one cabinet bank to the next.
The Amerock Kamari Series pull has a 5-1/16 inch (128 mm) center-to-center size, which sets the drilling span for mounting on cabinet doors and drawers.
The Amerock BP36823MB Kamari pull has an overall length of 6-3/16 inches, so it covers a moderate width on doors and drawers using the 5-1/16 inch hole spacing.
The Kamari matte black pull has a 1 inch projection, positioning the grip close to the cabinet face while still allowing space for fingers behind the pull.
The Amerock Kamari pull is made from zinc with a matte black finish, giving a metal construction with a non-reflective dark appearance on cabinets.
The Kamari Series pull has a width of 1-3/16 inches, providing a broad front surface for hand contact and a balanced look on doors and drawers.
The Amerock Kamari BP36823MB pull is specified with 8-32 x 1 inch screw size, which matches common cabinet hardware threading and length.
The Amerock Kamari 128mm matte black pull pairs a 5-1/16 inch center-to-center dimension with a 6-3/16 inch overall length, so it suits cabinets and drawers laid out on that boring span. With zinc construction, matte black finish, 1 inch projection, and 1-3/16 inch width, it delivers a consistent feel and look when repeated across a run of casework. Select this BP36823MB model when a 5-1/16 inch mounting pattern and a dark, streamlined pull are needed on a project.
Sold In: 1 Each