Amerock Kamari cabinet pull in golden champagne gives doors and drawers a defined grasp point, which helps users open and close fronts consistently without stressing the edge banding or finish. The pull is built from zinc, so the handle provides a solid-feeling contact surface that suits daily cabinet use in woodworking and installation projects. A 6-5/16 in (160 mm) center-to-center hole spacing drives the layout, letting installers align drilling patterns around a clear, repeatable dimension. Overall length of 7-7/16 in creates hand clearance across wider drawer fronts, helping users grip without catching fingers on the cabinet face. A 1 in projection sets the handle off the surface just enough to get fingers behind it while staying close to the door for a cleaner line. Width of 1-3/16 in offers a stable gripping area, which supports straight pulls and reduces side twist on mounting points.
The 6-5/16 in (160 mm) center-to-center dimension is the primary drilling reference, so layout lines can be struck from door or drawer edges to that fixed spacing for every handle run. With a 7-7/16 in overall length, the pull extends past the mounting holes, so installers can visually center the handle while trusting the pre-measured hole locations. A 1 in projection establishes how far the hand sits off the face, which is useful when planning clearance near adjacent doors or tall cabinet frames. The 1-3/16 in width keeps the pull compact from top to bottom, helping it sit comfortably on narrow rails while still giving enough purchase for users. Base dimensions of 3/8 in by 3/8 in define the footprint at each mounting point, which helps when checking flat mounting land on thinner rails or stile profiles.
The Amerock Kamari 6-5/16 pull uses a 160 mm center-to-center layout, which matches projects laid out on that metric spacing across cabinet runs. That fixed distance between mounting points simplifies planning when a job calls for repeating handles across doors, drawer banks, or tall pantry fronts. With its 7-7/16 in overall length, the pull suits medium to wider drawers where a longer handhold helps users grab at different points without losing leverage. The 1-3/16 in width lets the pull sit comfortably on typical cabinet rails, supporting use on both framed and frameless fronts where rail height may be limited. Zinc construction suits standard interior cabinet environments, so the pull integrates into decorative hardware plans alongside other metal components from the same project. The golden champagne finish can align with matching hinges or other trim pieces that share that color tone.
The 160 mm center-to-center spacing on this Amerock Kamari cabinet pull lets installers base jigs or drilling templates on a single, repeatable measurement, reducing layout variation from one cabinet to the next. The 1 in projection keeps the gripping area close to the door, which helps reduce bending loads on the fasteners when users pull straight out. Width of 1-3/16 in offers enough surface for multiple finger contact, supporting more even force across the handle during operation and easing strain on the mounting points. Base dimensions of 3/8 in by 3/8 in at each end concentrate the contact area, which is useful when positioning the feet fully on the flat section of a narrow rail. The golden champagne finish provides a consistent visible surface that installers can line up across a row, supporting straight visual alignment along cabinet faces.
The Amerock Kamari cabinet pull has a 6-5/16 in (160 mm) center-to-center spacing, which sets the drilling distance between mounting holes for consistent cabinet layouts.
The Amerock BP36824BBZ pull measures 7-7/16 in in overall length, giving a longer gripping area that works well on medium to wider cabinet drawers and doors.
The Kamari pull has a 1 in projection from the cabinet surface, allowing fingers to get behind the handle while keeping the profile relatively low on the door or drawer front.
The Amerock Kamari 6-5/16 pull is made from zinc, providing a metal construction that supports a solid feel during regular cabinet use.
Each mounting base on this Kamari pull measures 3/8 in by 3/8 in, which defines the footprint that sits on the cabinet rail or stile around the fastener location.
The Amerock Kamari golden champagne pull has a width of 1-3/16 in, giving a compact top-to-bottom profile while still offering a comfortable gripping surface on cabinet fronts.
The Amerock Kamari cabinet pull in golden champagne combines a 6-5/16 in (160 mm) center-to-center layout with a 7-7/16 in overall length, so it suits cabinet runs planned around that spacing and scale. Zinc construction and a 1-3/16 in width give a metal pull with a comfortable hand feel on typical doors and drawers. With its 1 in projection and 3/8 in by 3/8 in bases, the pull offers defined install reference points that support consistent results across a project.