Amerock Kamari 10-1/16 in pull is a cabinet handle designed for projects needing a 10-1/16 in center-to-center layout between mounting holes. That specific drilling dimension lets you match existing 10-1/16 in patterns on cabinet doors or drawers without altering hole locations. The pull is part of the Kamari collection from Amerock Corporation, so it ties into other Kamari pieces on a job when a consistent style is required. A center-to-center size of 256 mm also suits metric layout work, which helps when following European style cabinet plans. The pull uses zinc as the base material, giving a solid metal construction that supports regular cabinet use. Its matte black finish provides a dark, low-sheen look that works wherever a modern black handle is specified on furniture or built-ins.
The Amerock BP36826MB cabinet pull uses a 10-1/16 in center-to-center mounting pattern, so hole drilling or layout work centers on that exact spacing between the two screw locations. With an overall length of 11-1/4 in, the pull extends slightly beyond the drilling points on both sides, which helps when aligning it visually on wider drawer fronts or tall doors. The 1 in projection sets a predictable stand-off distance, giving room for fingers behind the pull while maintaining a relatively low profile against the cabinet face. At 1-3/16 in width, the pull presents a defined front edge that reads clearly on both narrow and wide faces, which helps during design coordination with surrounding hardware and trim.
The Kamari pull with a 256 mm center-to-center pattern is suited to cabinet doors and drawers laid out for 10-1/16 in drilling. That dimension aligns with projects following a 256 mm metric standard or 10-1/16 in imperial spacing, so it can serve both new builds and replacements where those measurements are already in place. The matte black finish lets this pull integrate into layouts calling for dark decorative hardware, and it coordinates with other matte black components in the space. As part of Amerock's Kamari collection, the pull supports design schemes where matching Kamari handles are used across base cabinets, wall cabinets, and furniture pieces. Its overall length of 11-1/4 in suits wider drawer fronts, where a longer pull helps span more of the width, and also fits tall doors where a more substantial handle is specified.
The 10-1/16 in (256 mm) center-to-center specification is the primary sizing reference for this Amerock cabinet pull, which simplifies template setup and repetitive drilling when multiple fronts share the same hardware layout. Knowing the projection is 1 in allows consistent planning for finger clearance, especially when doors open near walls or adjacent cabinets, since the pull will stand the same distance off the face every time. The 1-3/16 in width defines how the pull visually lands on rails and stiles, which helps in choosing its orientation and alignment relative to panel profiles and edge details. Base dimensions of 3/8 in by 3/8 in at each mounting foot give a clear footprint for marking and drilling during layout. The specified 8-32 x 1 in screw size describes the threaded connection between pull and cabinet front, which aids in matching screw length to the front thickness for repeatable fastening across a run of cabinets.
The pull has a 10-1/16 in (256 mm) center-to-center, 11-1/4 in overall length, 1 in projection, 1-3/16 in width, and 3/8 in by 3/8 in base dimensions for layout and sizing.
The BP36826MB pull uses zinc as the material, giving a metal construction suited to everyday cabinet door and drawer use where a solid handle is required.
The 10-1/16 in center-to-center size matches 256 mm layouts, so it fits cabinets drilled to that spacing and supports straightforward replacement or new drilling templates.
A 1 in projection sets how far the pull stands off the door or drawer, providing finger clearance while keeping the handle close for a tidy cabinet profile.
The matte black finish gives a dark, low-sheen look, helping the pull blend into black hardware schemes or contrast against lighter cabinet finishes as specified.
This Amerock Kamari pull uses 8-32 x 1 in screw size, so the threaded connection matches standard cabinet machine screw dimensions for door and drawer fronts.
The Amerock Kamari series BP36826MB pull combines a 10-1/16 in (256 mm) center-to-center pattern with a matte black finish and zinc construction, aligning with cabinet layouts calling for that drilling size. Its 11-1/4 in overall length, 1 in projection, and 1-3/16 in width define how it will sit and function on doors and drawers, helping you match this handle to your planned cabinet dimensions and visual design.