Berenson Brookridge Series 3-3/4" (96 mm) Center to Center Brushed Nickel Pull, - 2615-1BPN-P

Berenson Brookridge Brushed Nickel Pull For Cabinets

Berenson Brookridge brushed nickel pull gives cabinets a transitional look by combining the Brookridge collection styling with a Brushed Nickel finish, which works where a clean, modern-leaning appearance is needed without looking overly contemporary. The zinc material forms a sturdy handle body, so the pull stands up to regular door and drawer use in busy shops or lived-in kitchens. A 96 mm Center to Center mounting layout sets the hole spacing, which aligns with common drilling patterns for many cabinet lines that follow metric boring. The 4-3/16 inch overall length provides enough gripping surface across a standard drawer front, which helps when pulling heavier drawers in work areas. A Projection of 1-1/4 inches holds fingers off the cabinet face, reducing knuckle contact against the door or drawer front. The 15/32 inch Width keeps the pull visually light on smaller doors while still giving a definite grip line.

Key Brookridge Pull Details For Daily Use

• The 96 mm Center to Center dimension sets precise fastener spacing, which supports repeatable drilling setups across multiple cabinet runs during fabrication or installation.
• The Brushed Nickel finish controls surface sheen, which helps the pull visually coordinate with brushed faucets, hinges, and other nickel-finished decorative hardware in the same space.
• Zinc construction creates a solid-feeling pull body, which matters on frequently used drawers where a firm, consistent handhold is expected over time.
• The 4-3/16 inch overall Length defines how much handle spans the drawer front, which can affect how easily hands of different sizes catch the pull from various approach angles.
• The 1-1/4 inch Projection establishes stand-off from the cabinet face, which provides finger clearance for a comfortable grip even on thicker door edge profiles.
• The 15/32 inch Width keeps the pull from dominating narrow fronts, which is useful when laying out multiple handles across smaller doors or stacked drawer banks.

Installation Dimensions And Mounting Fit Details

The 96 mm Center to Center mounting on this Brookridge Series pull sets the distance between the two attachment points, so boring jigs can be set once and run across every door and drawer in the layout. A 4-3/16 inch overall Length places the grip slightly beyond the hole spacing on both sides, which helps visually balance the handle over the front panel. The 1-1/4 inch Projection defines how far the pull stands away from the face, so the hand naturally fits between the pull and the surface without scraping. With a Width of 15/32 inch and a Base dimension of 1/2 inch at each end, the pull seats in a compact footprint, which works on both standard stile widths and smaller drawer rails. The Brushed Nickel finish on the zinc body presents a consistent face at each mounting location, supporting a uniform line when multiple pulls are installed in sequence.

Using The Brookridge Pull In Cabinet Projects

Where This 96 Mm Brookridge Pull Fits Best

This Brookridge Series pull from Berenson Corporation is part of the Decorative Hardware & Moldings Handles and Pulls category, so it is positioned for cabinet and furniture door and drawer applications. The Transitional style description signals that the pull bridges traditional and contemporary cabinet designs, which works in projects aiming for an updated look without abandoning classic profiles. The Brushed Nickel finish pairs naturally with other nickel-toned components, which matters in kitchens or built-ins where hinges, faucets, and decorative hardware are expected to read as one coordinated set. Its zinc Material supports use on high-touch fronts such as kitchen base cabinets, utility cabinets, or shop storage, where the pull is frequently grabbed throughout the day. The 4-3/16 inch Length helps the pull sit comfortably across typical residential drawer widths, which assists in laying out balanced hardware lines on banks of drawers.

The 96 mm Center to Center value is especially useful in projects using metric-based cabinet systems, since that spacing is a common standard for drawer and door pulls in many lines. When repeating that spacing across a room, installers can rely on the same jig positioning for every front, which keeps lines straight and reduces layout variation between pieces. The 1-1/4 inch Projection helps when doors are close to adjacent walls or appliances, because the hand can hook the pull from the side with enough clearance between the pull and the front. The 15/32 inch Width allows this handle to be used on narrower rails or smaller doors, where a deeper or wider pull might crowd panel details. The Base size of 1/2 inch provides a defined landing area at each mounting point, which visually anchors the pull against the surface and can help mask minor drill tear-out at the hole edges.

Why Brookridge Dimensions Support Consistent Results

The specified 96 mm Center to Center dimension drives repeatability, because once that spacing is dialed into a boring template, holes can be drilled quickly across multiple cabinet fronts while keeping hardware alignment true. With the overall 4-3/16 inch Length, hardware lines stay visually proportional to standard door and drawer sizes, which helps when matching pulls across upper and lower cabinetry. The 1-1/4 inch Projection works as a built-in clearance spec, letting fabricators anticipate how far hardware will extend into walkways or working zones relative to doors and drawer faces. A 15/32 inch Width paired with a 1/2 inch Base lets the pull sit firmly without covering excessive panel detail, so stile profiles, edge treatments, or narrow rails remain visible while still supporting a secure mounting area. The Brushed Nickel finish also contributes to consistent field results by presenting a uniform, low-glare surface that reads the same under varied lighting, which keeps hardware runs looking even from cabinet to cabinet.

The zinc Material supports predictable machining at the factory level, which contributes to uniform threads for the mounting interface described by the 8-32 designation in the Web Description. That consistent threading engages with matching fasteners in a repeatable way, which is useful when hardware is installed across dozens of fronts in a single project. Because this pull is identified by the Manufacturer Part # 2615-1BPN-P and the SAP description "BROOKRIDGE PULL 96MM CC BRSH NKL," matching additional units to an existing job later is straightforward, which matters when expanding a run of cabinets or replacing fronts while keeping hardware identical. Being part of the Berenson product class for Handles and Pulls means this piece is designed as a functioning handle rather than decorative trim, so its dimensions and material choices are structured around practical gripping and regular operation in cabinetry.

Common Brookridge Brushed Nickel Pull Questions

Select This Brookridge Pull For Consistent Cabinet Lines

The Berenson Brookridge Series 3-3/4 inch (96 mm) Center to Center Brushed Nickel pull brings a Transitional style, zinc construction, and defined dimensions together for practical cabinet work. With a 96 mm Center to Center layout, 4-3/16 inch overall length, 1-1/4 inch projection, 15/32 inch width, and 1/2 inch base, this pull supports consistent drilling, clean alignment, and comfortable gripping across doors and drawers. For projects built around brushed nickel decorative hardware, this Brookridge pull keeps finishes and proportions coordinated from one cabinet front to the next.