Hickory Hardware Forge Pull For Cabinets

Hickory Hardware Forge pull identifies this Belwith Keeler handle as part of a decorative hardware line aimed at cabinets and similar projects. The 5-1/16 inch length with 128 mm center to center mounting gives a standardized hole spacing that supports straightforward layout on doors and drawers. The satin nickel finish provides a neutral metallic look that pairs with a wide range of hinge and fixture finishes in kitchen, bath, or shop environments. As a handle and pull from the decorative hardware and moldings category, it is suited to both new cabinet builds and refresh work where visual consistency matters. The manufacturer part number H076702-SN gives installers and buyers a precise reference that helps repeat the same style across multiple openings.

Key Forge Series Pull Details That Matter

• The 128 mm center to center mounting dimension sets hole spacing, which streamlines drilling patterns and speeds repeatable layout across multiple cabinet fronts on a run.
• The 5-1/16 inch overall sizing defines the visual footprint on the face of a door or drawer, helping balance handle scale with rail widths and panel proportions.
• The satin nickel finish delivers a brushed silver tone that coordinates with many hinge styles and faucets, supporting cohesive hardware appearance across a room.
• Placement in the decorative hardware and moldings handles and pulls class confirms its role as a visible cabinet touchpoint rather than concealed functional hardware.
• Brand association with Belwith Keeler positions the pull within a long-standing decorative cabinet hardware portfolio, aiding pattern matching on future jobs.

128 Mm Center To Center Pull Mounting

The 128 mm center to center specification sets the distance between mounting points on this satin nickel cabinet pull, so installers can rely on a known spacing when laying out new fronts. This dimension supports efficient use of drilling jigs that reference metric hole patterns. Classified under handles and pulls, the design expects mounting through the cabinet face, which suits standard framed or frameless construction using typical boring practices. The 5-1/16 inch overall size relates closely to the 128 mm spacing, so sightlines remain balanced once the pull is fastened. With the manufacturer part number H076702-SN tied to this configuration, matching replacement or additional pulls on later phases stays straightforward.

Using This Satin Nickel Cabinet Pull Well

Where The Forge Series Pull Works Best

This Belwith Keeler cabinet pull sits in the decorative hardware and moldings category, aligning it with visible cabinet locations such as kitchen, bath, and built-in storage fronts. The satin nickel finish creates a brushed silver tone that pairs with many existing hinge and fixture finishes, which helps when tying new fronts into an established room scheme. With its 5-1/16 inch overall length, the pull suits medium-width drawers and doors where a modestly sized handle fits the rail without crowding edge profiles. The 128 mm center to center mounting spacing supports use on cabinet runs that already follow this common metric standard, promoting visual and dimensional consistency from one opening to the next.

Details That Support Consistent Install Results

The 128 mm center to center pull layout lets installers set up jigs once and repeat clean, aligned boring across an entire project, reducing layout variation between doors and drawers. Because the overall pull length is defined as 5-1/16 inch, installers can anticipate overhang past the mounting holes and position the handle to clear adjacent hardware or trim details. The satin nickel finish contributes a uniform surface appearance across multiple pulls in the same space, which is important when hardware lines up along cabinet banks. The fixed manufacturer part number H076702-SN anchors ordering and documentation, so future phases or service work can call out the exact same satin nickel cabinet pull without confusion.

Common Questions About H076702-SN Pull Use

Select This Pull For 128 Mm Cabinet Runs

The defined 128 mm center to center spacing, 5-1/16 inch length, and satin nickel finish make this Hickory Hardware Forge pull a practical choice when a consistent metric layout and coordinated brushed silver appearance are priorities. As a Belwith Keeler handle in the decorative hardware and moldings category, it fits projects that call for repeatable cabinet detailing alongside other visible fittings. Referencing the H076702-SN part number aligns ordering and installation with the exact style and dimensions used elsewhere on the job.