1/4" x 48" Guide/Track Assembly, Clear Anodized Finish

1/4 x 48 Guide Track Assembly For Sliding Doors

1/4 x 48 Guide Track Assembly describes an EPCO aluminum guide and track setup sized for 1/4 inch thick doors, so installers can match the hardware to wood or glass panels without reworking the opening. The 4 ft long aluminum track supports sliding door runs up to that length in one piece, which helps keep movement straight over typical cabinet or casework spans. The clear anodized finish on the aluminum provides a stable surface treatment, so the track looks consistent and resists surface wear in normal use. This assembly is part of EPCO sliding door hardware for heavier 1/4 inch thick wood or glass doors, so it is intended to carry more demanding panels within that thickness. The product is identified by manufacturer part number 1-A-4, which ties directly to EPCO documentation and job submittals.

Sliding Door Track Details That Support Daily Use

• The EPCO aluminum construction gives the guide and track a rigid base, which helps sliding doors stay aligned under regular operation on cabinets, cases, or similar installations.
• The 4 ft long track section spans common door openings in a single length, which reduces joint points and helps the door travel feel smoother along the full run.
• The clear anodized finish on the aluminum creates a consistent surface, which helps the track blend with surrounding hardware and limits finish changes over time.
• The design is specified for heavier 1/4 inch thick wood or glass doors, which lets installers use substantial panels within that thickness range in a supported way.
• The upper guide labeled #48A14-A and the track labeled #38AS14-A give clear component identities, which simplifies matching parts on drawings and during field replacements.
• The bottom track uses machined, hardened fiber inserts, which provides a defined bearing surface for the door edge and supports long-term sliding contact.

Guide Track Layout And Installation Considerations

This EPCO sliding door hardware uses an upper guide identified as #48A14-A together with a track identified as #38AS14-A, so installers can position a coordinated top guiding system over the 4 ft span. The bottom track has machined, hardened fiber inserts, which gives the lower edge of the 1/4 inch door a controlled running surface along the full length. The clear anodized aluminum material keeps the track profile and finish stable while the door moves, which supports predictable clearances between the track and door edge. By matching this assembly to heavier 1/4 inch thick wood or glass doors, installers can plan their layout knowing the track is intended for that door thickness and weight category.

Using This 1-A-4 Track Assembly On Projects

Where This 1/4 Inch Door Track Fits Best

This EPCO 1-A-4 aluminum guide and track assembly is specified for heavier 1/4 inch thick wood or glass doors, so it suits sliding panels in casework, cabinets, or partitions using that material thickness. The 4 ft long track allows a single continuous run for openings up to that length, which is useful on wider cabinet fronts or built-ins where a splice would disrupt travel. Being part of EPCO sliding door hardware, the assembly integrates into projects that standardize on that manufacturer, which helps maintain consistent components across a job. The clear anodized finish supports use in visible areas where the track sits near finished faces or trim and needs a neutral, stable appearance.

Why These Guide And Track Details Matter

The aluminum construction of the upper guide #48A14-A and track #38AS14-A provides a stable framework, which helps sliding doors resist sagging or binding across repeated cycles. The bottom track with machined, hardened fiber inserts creates a defined wear surface, which helps the 1/4 inch door edge move predictably without cutting into the metal base of the track. Because this assembly is designed for heavier 1/4 inch thick wood or glass doors, installers can select door materials in that thickness knowing the hardware is intended to handle that application. The 4 ft length simplifies layout, because one piece establishes the full sliding path, which supports clean alignment between the upper guide and lower fiber-lined track from one end to the other.

Common Questions About This EPCO Sliding Track

Selecting This Track For 1/4 Inch Door Projects

The EPCO 1/4 x 48 Guide Track Assembly with clear anodized aluminum, upper guide #48A14-A, track #38AS14-A, and bottom hardened fiber inserts is built for heavier 1/4 inch thick wood or glass doors. For sliding cabinet, casework, or similar projects matching that thickness and a 4 ft run, this assembly provides an identified, coordinated guide and track solution ready to integrate into project drawings and material lists.