EPCO Architectural Series stainless steel pull provides a long 320mm center-to-center grip that spreads hand contact across wider cabinet or door fronts, which helps create a consistent, aligned look across multiple panels in a run. The stainless steel handle design supports decorative hardware layouts where a modern, linear pull is preferred, so it suits cabinetry or casework that needs clean, straight lines. With a manufacturer part number AS52-320-SS, this pull matches EPCO documentation for ordering and job takeoffs, which simplifies repeat purchasing across multiple projects. The handle functions as part of the Decorative Hardware & Moldings category under Handles and Pulls, so it fits into standard hardware planning for kitchens, baths, and built-ins. This pull also fits workflows that call for EPCO handles and pulls, allowing installers to keep the same visual language across a project.
The stainless steel handle 320mm CC layout uses a fixed center-to-center distance, so installers can base drilling templates directly on that 320mm spacing when setting up doors and drawer fronts. The overall length of 412mm means the pull extends well past the mounting points, which affects where it sits relative to panel edges and stiles. With a projection of 35mm, or 1.38 inch, from the mounting surface, this handle stands off the face enough to accommodate typical finger clearance while keeping the pull profile relatively close to the door. These dimensions collectively shape drilling patterns, edge setbacks, and visual positioning, which matters when aligning multiple EPCO handles and pulls across a full bank of cabinetry.
The 320mm center to center stainless steel pull fits applications that benefit from a longer handle, such as wider cabinet doors or large drawers, because the extended grip spans more of the panel width. Its 412mm overall length suits layouts where the handle is intended to act as a strong horizontal or vertical visual element, tying several fronts together in a straight line. As part of the EPCO Architectural Series, this handle works in decorative hardware plans that call for a defined, architectural look using stainless steel pulls. The pull sits within the Decorative Hardware & Moldings Handles and Pulls category, so it integrates naturally into cabinet hardware schedules that group pulls, knobs, and related components together for ordering.
The AS52-320-SS stainless steel handle uses a precise 320mm center-to-center dimension, which supports jig-based drilling and consistent spacing from one cabinet to the next, reducing layout variation across a project. The 35mm, or 1.38 inch, projection controls how far the handle stands off the surface, helping maintain a uniform shadow line when multiple pulls are mounted in rows or banks. With a 412mm overall length, each pull reads visually proportional on larger fronts, which supports hardware alignment with rails and stiles in planned elevations. Having a defined manufacturer part number AS52-320-SS and a clear SAP description of "STAINLESS STEEL HANDLE,16.22INL,320MM CC" aids documentation on drawings and cutlists, so installers and shops can reference the same handle consistently from design through installation.
The EPCO Architectural Series stainless steel pull has a 320mm center-to-center dimension, which defines the mounting hole spacing used when laying out cabinet doors and drawers.
The AS52-320-SS stainless steel handle has an overall length of 412mm, allowing it to span a wider section of the cabinet or drawer front for a longer visual line.
The EPCO pull projects 35mm, or 1.38 inch, from the mounting surface, providing finger clearance behind the handle while keeping a relatively low profile on the cabinet face.
This handle is in the Decorative Hardware & Moldings category under Handles and Pulls, so it fits standard cabinet hardware planning and selection.
The manufacturer part number is AS52-320-SS, which matches EPCO documentation and supports accurate ordering and project specification.
In SAP records, this pull is described as "STAINLESS STEEL HANDLE,16.22INL,320MM CC," reflecting its length and center-to-center spacing for system tracking.
The EPCO Architectural Series stainless steel pull with 320mm center-to-center spacing, 412mm overall length, and 35mm projection offers defined dimensions that simplify layout across cabinet runs. Its SAP description and AS52-320-SS part number connect clearly to ordering and documentation tasks. For projects that specify Decorative Hardware & Moldings in the Handles and Pulls class, these details help align shop drawings and installation steps to the same stainless handle choice.
Sold In: 1 Each