EPCO recessed pull provides a low-profile grip by sitting into the door or panel rather than on top of it, which keeps the hardware out of the way in tighter clearances or along sliding paths. The 2-7/8 inch center to center drilling gives a familiar mounting layout, so it lines up with standard pull boring in many shop workflows. Overall 3-19/32 inch length keeps the pull compact on smaller doors or drawers while still giving a defined hand contact area. The 9/16 inch projection keeps the pull shallow from the surface, so it does not interfere as much with adjacent fronts or passes. Almond color ties visually to light finishes, helping the pull blend into painted or laminate surfaces. Plastic material keeps the pull light in weight, so it suits cabinet doors and drawer fronts without adding noticeable load.
The pull mounts into a 3-1/8 x 1-1/4 x 7/16 inch hole, so the cutout dimensions govern how cleanly the flange sits against the cabinet surface. That mortise depth of 7/16 inch controls how far the body recesses into the panel, which keeps the remaining projection at 9/16 inch for finger access. Center to center spacing of 2-7/8 inch establishes the distance between fasteners, so drilling remains straightforward when matching typical handle layouts. The 3-19/32 inch length extends slightly beyond the mounting span, which leaves material at each end for a stable bearing surface on the face of the door or drawer. Plastic material pairs with this recessed mounting to distribute pressure around the flange, helping the pull sit snugly in the routed opening.
The almond recessed pull works on cabinet doors or drawer fronts where a flush or low-profile grip is preferred, because it mounts into a 3-1/8 x 1-1/4 x 7/16 inch cutout that brings most of the body inside the panel. The 3-19/32 inch length suits many residential or light commercial cabinet fronts, giving enough visible hardware to locate by sight while staying compact on smaller faces. Almond coloring coordinates with lighter cabinet finishes, so it integrates easily into layouts that use neutral or warm light tones. The 2-7/8 inch center to center mounting dimension aligns with a common drilling pattern for pulls, which helps when standardizing boring setups across multiple doors and drawers on a job.
The defined 3-1/8 x 1-1/4 x 7/16 inch hole size allows repeatable routing or drilling templates, which helps each EPCO recessed pull sit at the same depth and alignment across a bank of cabinets. The 9/16 inch projection from the surface creates a predictable grip depth, which is important for keeping user feel similar from one opening to another. Center to center spacing at 2-7/8 inch lets installers rely on a single boring pattern, reducing layout variation between different cabinet lines using this DP1710-AL recessed pull. The overall 3-19/32 inch length gives a consistent hardware span to reference off door edges or rails, tightening visual alignment across paired doors. Plastic construction supports this repeatability by providing a stable molded shape, which helps edges register neatly against the machined opening for a uniform finished look.
The EPCO recessed pull uses 2-7/8 inch center to center mounting, which sets the distance between fastener locations and helps align with standard pull drilling patterns.
The DP1710-AL recessed pull mounts into a 3-1/8 x 1-1/4 x 7/16 inch hole, which defines the routed pocket needed for the body to sit recessed in the panel.
The almond recessed pull has a 9/16 inch projection, which provides finger clearance while keeping the pull profile relatively shallow on the cabinet face.
The EPCO DP1710-AL recessed pull has a 3-19/32 inch overall length, which defines its footprint and helps with centering on doors or drawer fronts.
The EPCO recessed pull is made from plastic, which provides a molded body that seats uniformly in the cutout against the cabinet surface.
The DP1710-AL recessed pull is almond, which coordinates with lighter cabinet finishes for a unified appearance across doors and drawers.
This EPCO recessed pull with 2-7/8 inch center to center spacing, 3-19/32 inch length, and 9/16 inch projection offers fixed dimensions that integrate smoothly into cabinet layouts. The 3-1/8 x 1-1/4 x 7/16 inch mounting hole and plastic construction support consistent routing patterns and seating across multiple fronts. By choosing the almond DP1710-AL recessed pull, projects gain a low-profile grip that matches these established measurements for repeatable shop and field installations.
Sold In: 1 Each