EPCO DP403-B drawer pull is an aluminum tab pull in anodized satin brass that provides a low-profile grip at the top of the drawer front, giving a clean look while still allowing a solid handhold. The 1-7/8 inch (48 mm) center to center drilling lines up the mounting points for a compact pull, which helps on smaller drawer fronts or tight layouts where larger handles crowd the face. The 3-7/8 inch overall length spreads the pull visually across more of the drawer edge, which balances the appearance on standard cabinet widths. The top mounting design positions the pull over the edge of the front, so the installer works from the top face, which is useful on slab fronts where a hidden grip is preferred. The anodized satin brass finish gives a consistent brass tone, which supports uniform appearance across multiple drawers.
This EPCO aluminum cabinet pull is designed for material thickness of 5/8 to 7/8 inch, which tells the installer the range of drawer or door fronts where the top-mounted lip will seat correctly. Within this thickness range, the pull wraps the edge as intended, so the gripping surface sits where fingers naturally catch the tab. The center to center drilling at 1-7/8 inch works with that thickness range by setting the screw positions at a depth that keeps the pull tight to the face. The top mounting orientation focuses all work on the accessible outer side of the front, which streamlines installation on prefinished parts and supports consistent alignment along the upper edge.
The EPCO 1-7/8 inch center to center anodized satin brass tab pull is suited to drawer fronts and cabinet fronts that measure between 5/8 and 7/8 inch thick, because that is the material range it is designed to fit. On these fronts, the top mounting style places the grip along the upper edge, so the user pulls from a thin exposed lip instead of a projection, which is useful on contemporary, flat-panel cabinetry. The 3-7/8 inch length means the pull spans a modest portion of the drawer width, which helps maintain proportion on smaller drawers while still offering enough surface area for a comfortable pull. The aluminum body keeps the profile visually light, and with the anodized satin brass finish, the hardware can align with other brass-toned elements in the same room.
The 1-7/8 inch center to center measurement on the DP403-B defines the exact drilling pattern, which supports the use of fixed jigs so every pull in a run sits at the same location and orientation. The top mounting style means all holes are referenced from the top edge of the drawer front, giving a clear datum for layout and reducing variation from piece to piece. The specified 5/8 to 7/8 inch material thickness range keeps the mounting geometry consistent, so the pull lip projects and seats the same way across different cabinet sections. The 3-7/8 inch overall length provides a fixed visible span that installers can use to align pulls relative to door or drawer margins. The anodized satin brass finish applied to the aluminum surface delivers a uniform sheen, which helps multiple pulls read as a continuous design line when installed across a full run of cabinetry.
The EPCO DP403-B drawer pull has a 1-7/8 inch center to center measurement, which sets the exact screw spacing for drilling and layout across drawer fronts.
The tab pull length is 3-7/8 inch, giving a moderate span along the drawer edge that balances appearance and grip area on typical cabinet fronts.
The EPCO DP403-B drawer pull is made from aluminum with an anodized satin brass finish, providing a brass-colored appearance on a lightweight metal body.
This aluminum tab pull is specified for material thickness from 5/8 to 7/8 inch, which aligns the top-mounted lip and screw positions on standard cabinet fronts.
The DP403-B is a top mounting pull, so it installs along the top edge of the front, placing the gripping tab where fingers naturally catch.
The DP403-B designation identifies this specific aluminum, anodized satin brass, 1-7/8 inch center to center, 3-7/8 inch length drawer pull for ordering and reordering.
The EPCO DP403-B drawer pull combines a 1-7/8 inch center to center pattern, 3-7/8 inch length, and top mounting layout, giving a defined drilling scheme and clean tab-style grip. With aluminum construction, anodized satin brass finish, and a design tuned to 5/8 to 7/8 inch material thickness, this pull aligns with modern cabinet fronts and repeatable shop workflows. Use the DP403-B part number when specifying hardware so every drawer in the run matches in size, finish, and mounting geometry.
Sold In: 1 Each