Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO Edge Series tab pull gives a low-profile grip point along the cabinet edge, so doors and drawers open without protruding handles in the way. The anodized satin brass finish provides a consistent brass look that fits decorative hardware projects where a warm metal tone is needed. With a center to center of 1-7/8 inches, this pull sets a tight screw spread that suits compact door and drawer fronts often used in modern cabinetry. The 3-7/8 inch overall length creates a broader finger contact area, which helps when multiple users grab the same point every day. Back mounted installation keeps fasteners hidden from the front, which maintains a clean face while the pull anchors from the rear. As a cabinet edge pull from EPCO, this part aligns with typical woodworking layouts where installers want a simple, repeatable solution.
The back mounted design means the pull fastens from the rear of the cabinet material, so the visible edge stays uninterrupted while the grip is secured from inside the door or drawer. Designed for material thickness from 1/2 inch to 7/8 inch, this pull works with common cabinet stock sizes and lets installers plan for standard panel builds without altering thickness for the hardware. The specified #6 x 5/8 inch screws match the pull geometry, helping the threads engage reliably in the panel while keeping the point within typical cabinet wall depths. Because center to center is fixed at 1-7/8 inches, jigs or drilling templates can be set once and reused across a run of fronts.
This EPCO Edge Series tab pull in anodized satin brass fits decorative hardware layouts where a slim pull at the cabinet edge is preferred over larger handles. The 3-7/8 inch length suits smaller doors and drawers commonly found in kitchen, bath, and built-in cabinetry, where front space is limited and a compact pull is needed. Its 1-7/8 inch center to center screw spacing aligns well with narrow stile widths, allowing the pull to sit comfortably near the edge without crowding adjacent hardware. As a handle within the Decorative Hardware & Moldings, Handles and Pulls class, it supports woodworking projects that call for coordinated metal details across multiple fronts. The satin brass finish lets this pull tie into other brass-toned components in the same installation, so casework, trim, and pulls follow a unified hardware theme through the space.
The tab pull is back mounted, so installers work from the inside face when anchoring, which keeps the outer surface clear and reduces layout steps on the finished front. With a defined material thickness range of 1/2 inch to 7/8 inch, the pull geometry and screw length are set to seat properly in standard cabinet panels, which helps avoid over-penetration into adjoining cavities. The fixed 1-7/8 inch center to center dimension lets a single drilling pattern control alignment, improving speed and keeping a straight visual line when multiple pulls are installed in sequence. Overall length at 3-7/8 inches creates a predictable reveal along the edge, which helps when aligning pulls to panel corners or to neighboring fronts in a bank of cabinets. Using the DP40-B manufacturer part number ties each order back to the exact EPCO Edge Series component, simplifying job documentation and later field replacements.
The EPCO Edge Series tab pull has a 1-7/8 inch center to center, so screw holes are spaced for compact doors and drawers where narrower hardware spacing is required.
The DP40-B pull measures 3-7/8 inches in length, giving a wider gripping edge along the cabinet front while still fitting smaller doors and drawer faces.
This EPCO tab pull is designed for material thickness from 1/2 inch to 7/8 inch, matching typical cabinet panel dimensions in many woodworking projects.
The EPCO Edge Series tab pull is back mounted, so it is fastened from the rear of the cabinet material, leaving the front edge clean and uninterrupted.
The DP40-B pull uses an anodized satin brass finish, providing a controlled brass tone that coordinates with other brass decorative hardware in the same project.
This EPCO tab pull is specified with #6 x 5/8 inch screws, so the threads engage within typical cabinet material depths while staying compatible with the pull geometry.
The EPCO Edge Series 1-7/8 inch center to center anodized satin brass tab pull pairs a compact screw spread with a 3-7/8 inch length, making it suited to smaller cabinet fronts that still need a solid gripping edge. Its back mounted design and 1/2 inch to 7/8 inch material range align with standard cabinet construction practices, so layout and drilling can follow familiar steps. Specify the DP40-B part when a satin brass EPCO edge pull is required across a project and consistent appearance and dimensions matter.
Sold In: 1 Each