Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO Edge Series tab pull gives a low-profile grip point with a 1-7/8 inch center to center spacing, so doors and drawers open consistently where installers expect the hand contact. The overall 3-7/8 inch length spreads that pull force over more edge, which helps the hardware sit stable across everyday use. The anodized oil rubbed bronze finish provides a dark, uniform appearance that matches other oil rubbed bronze decorative hardware on the job. The DP40-ORB part number identifies this specific size and finish combination, which simplifies reordering the same pull across a project. Polybagged supply protects the finish from jobsite handling before installation and during transport. As part of EPCO decorative hardware and moldings, this pull fits projects calling for edge-style cabinet handles and pulls in an oil rubbed bronze look.
This EPCO tab pull is back mounted, so it fastens from the inside face through to the pull, giving a secure connection while leaving the front edge uncluttered. It is designed for material thickness from 1/2 inch to 7/8 inch, which covers common cabinet door and drawer front construction in many woodworking projects. That stated thickness range means the pull is sized for typical residential and light commercial cabinet stock without extra shimming. Center to center at 1-7/8 inch keeps the mounting points close enough for narrow fronts, while the 3-7/8 inch length still provides a useful tab surface at the edge.
The EPCO Edge Series tab pull in anodized oil rubbed bronze fits cabinet doors and drawer fronts built in thicknesses from 1/2 inch to 7/8 inch, so it works across many standard face-frame and frameless cabinet designs. The 1-7/8 inch center to center drilling makes it suitable for smaller drawer fronts and doors where wider hole spacing would crowd edges or stile areas. With a 3-7/8 inch length, the pull presents a modest but usable tab along the panel edge, which supports consistent gripping without visually dominating narrow fronts. The oil rubbed bronze finish aligns with projects that specify darker, traditional-toned decorative hardware and moldings, tying pulls to hinges and other handles in similar finishes.
The defined 1-7/8 inch center to center spacing on this DP40-ORB tab pull standardizes hole locations, which helps installers keep handles aligned across doors and drawers along a run. Once a drilling jig is set to that spacing, the same setting carries through the entire job, saving layout time. The 3-7/8 inch overall length gives a repeatable visual proportion from piece to piece, which keeps fronts looking aligned when viewed along a bank of cabinets. Because the manufacturer part number DP40-ORB uniquely identifies this specific Edge Series pull, that code can be used to match existing installations when additional cabinets are added or when a pull is replaced. The material thickness range from 1/2 inch to 7/8 inch anchors expectations about where this back mounted design is intended to be used, supporting consistent hardware selection across similar cabinet constructions.
The EPCO Edge Series DP40-ORB tab pull has a 1-7/8 inch center to center dimension, which sets the drilling distance between mounting holes for consistent cabinet layouts.
The tab pull length is 3-7/8 inch, so it spreads the gripping area along more of the door or drawer edge for comfortable everyday cabinet operation.
The back mounted EPCO tab pull fastens from the inside face through to the pull, leaving only the slim tab visible on the front for a clean edge appearance.
This DP40-ORB pull is specified for material thickness from 1/2 inch to 7/8 inch, matching many standard cabinet door and drawer front constructions.
The EPCO DP40-ORB tab pull has an anodized oil rubbed bronze finish, providing a dark, coordinated look with other oil rubbed bronze decorative hardware.
The DP40-ORB manufacturer part number identifies this exact size and finish, which simplifies specifying, ordering, and matching pulls across multiple cabinets.
The EPCO Edge Series tab pull DP40-ORB pairs a 1-7/8 inch center to center layout with a 3-7/8 inch length and back mounted design, giving a clean edge grip for doors and drawers. With its anodized oil rubbed bronze finish and material range from 1/2 inch to 7/8 inch, it fits many cabinet constructions that call for darker decorative hardware. Selecting this specific part number keeps sizing, finish, and mounting style consistent across the project.
Sold In: 1 Each