Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO 72 inch aluminum tab pull gives you a continuous 6 foot pulling edge for doors or panels that need a clean, uninterrupted line across the run. The 72 inch (1829 mm) length supports wide cabinet sections or multiple fronts in one piece, which cuts layout breaks and keeps faces visually aligned on longer installations. The pull is made from aluminum, so it adds very little weight to the door or drawer front while still giving a solid gripping edge in daily use. Its tab pull design keeps hardware low profile at the edge of the material, which helps maintain a flat cabinet face with minimal projection. The pull is part of the EPCO handles and pulls line, so it fits into decorative hardware layouts that call for coordinated components across a project.
This EPCO tab pull uses flush mortise mounting, so the profile sits into a cutout along the edge rather than projecting off the face. That mounting style helps the pull follow the cabinet edge cleanly and minimizes snag points when doors are open or closed. The pull is specified for material thickness of 13/16 inch, giving installers a clear target thickness when selecting door or drawer fronts for the profile. Matching the 13/16 inch thickness helps the mortise depth and tab geometry work together so the pull nests into the edge while still leaving enough material for strength around the cut. The aluminum construction keeps the mortised section light, which is helpful on wider doors where edge hardware extends the full height or width.
The EPCO 72 inch aluminum tab pull fits projects where a long, continuous grip is preferred, such as wide base cabinets, tall pantry doors, or multiple aligned drawers along a run. Because the profile is designed for flush mortise mounting, it suits frameless or slab-style fronts where the pull is cut into the edge rather than applied on the face. The 6 foot length supports layouts that call for a single piece across several aligned fronts, helping maintain a straight visual line from one end of the cabinet bank to the other. Being part of the decorative handles and pulls category, this tab pull works as the primary edge hardware in modern cabinet designs that favor a low-profile pull instead of bulkier handle projections.
The anodized satin clear aluminum construction gives this tab pull a finished metallic look along the entire 72 inch length, which keeps the edge appearance consistent from end to end on long doors or drawer banks. Aluminum also keeps overall weight down, which is important when the pull runs the full length of a tall panel and the hardware mass shifts to the edge. The specified fit for 13/16 inch material gives a clear dimension target so the mortise depth and pull profile line up, supporting repeatable results from one cabinet front to the next on a job. The flush mortise mounting detail allows the finger grip to sit close to the face plane, which can help maintain tight reveals between adjacent doors without the pull bodies touching. The EPCO DP412-2-LA designation ties this specific length and configuration to the EPCO line, which helps installers and shops repeat the same profile specification when they need the same tab pull on future projects.
The EPCO DP412-2-LA tab pull has a length of 72 inches, or 1829 mm, which allows it to span wide cabinet sections or tall doors in a single continuous piece.
This EPCO 72 inch aluminum tab pull uses flush mortise mounting, so it is set into the edge of the material, keeping the pulling surface nearly level with the cabinet face.
The tab pull is specified for material thickness of 13/16 inch, aligning the mortise depth and pull profile to that stock dimension for a proper seat along the edge.
The 6 foot EPCO tab pull has an anodized satin clear aluminum finish, providing a neutral metallic appearance that coordinates with many cabinet color schemes.
This flush mortise mounting tab pull is typically used on cabinet doors or drawer fronts where a low-profile, edge-grip solution is preferred over a projecting handle.
The tab pull is manufactured by EPCO, with manufacturer part number DP412-2-LA, which identifies this 72 inch anodized satin clear aluminum version.
The EPCO 72 inch aluminum tab pull, DP412-2-LA, delivers a 6 foot continuous grip, flush mortise mounting, and a fit tuned to 13/16 inch material. Those details support clean-lined cabinet work where a long, low-profile pull along the edge is the design goal. The anodized satin clear aluminum finish keeps the pull visually neutral across different door and drawer colors, which helps standardize one profile across an entire room. For projects that call for a single tab pull type across base cabinets, tall units, or aligned drawer banks, this EPCO model offers a defined length, mounting style, and material thickness target that can be specified and repeated.
Sold In: 1 Each