Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO 3 inch satin bronze tab pull provides a low-profile grip point using a 3 inch center to center layout, so drilling lines stay simple and consistent across doors and drawers on a run of cabinets. The 3-7/8 inch overall length gives a little extra metal beyond the mounting centers, which helps visually frame the edge of the door while keeping the pull compact. An anodized satin bronze finish puts a muted metallic color on the pull, so it reads as decorative hardware without the high glare of a bright finish in finished woodworking projects. This tab pull sits in a flush mortise, so it works as an edge pull that does not project as far off the surface as surface-mounted pulls. Designed for 3/4 inch material thickness, it matches standard cabinet door and drawer front stock so layout and mortising can be repeated from piece to piece.
The flush mortise mounting on this EPCO DP412-BZ tab pull means the body is recessed into the edge of the cabinet component, so only the working lip stands proud and the rest sits level with the surface. This style helps keep lines clean across panels because the pull does not add extra projection beyond the designed lip. The pull is specified for material thickness of 3/4 inch, so standard cabinet door and drawer front stock aligns with the pull geometry and places the grip where fingers naturally reach along the top or side edge. With 3 inch center to center spacing, drilling or boring for the #6 x 5/8 inch screws can follow a simple two-hole pattern that repeats across all fronts, which helps speed layout on larger banks of cabinetry.
The EPCO DP412-BZ tab pull is set up for installation on 3/4 inch thick cabinet material, so it suits typical framed or frameless cabinet doors and drawer fronts that use that stock. Because the pull uses a 3 inch center to center spacing, it can be positioned near a top edge on drawers or at a vertical edge on doors while still keeping both mounting points well within the material. The 3-7/8 inch overall length gives a little extension beyond the mounting holes, so when it is mortised flush, the visible tab defines a clear grab point along the edge. The flush mortise mounting keeps the body of the pull in line with the door or drawer face, which helps maintain a flat front elevation across multiple units in a bank, even when several pulls sit in close proximity.
The 3 inch center to center dimension on this anodized satin bronze tab pull simplifies jig setup, because once a jig is built for two mounting points at that spacing, it can be reused across every matching front. The 3-7/8 inch length ties into that spacing by keeping a predictable amount of metal at each end, which helps installers visually align pulls from piece to piece along a run of cabinets. The specification for 3/4 inch material thickness guides mortise depth and placement so the pull sits properly without over-cutting into thinner stock, which supports a tight fit at the edge. The anodized satin bronze finish supplies a uniform color and sheen on the pull surface, so when multiple EPCO tab pulls are installed in the same area, they present a consistent appearance that matches other satin bronze handles and pulls in the project.
The EPCO DP412-BZ tab pull has a 3 inch center to center mounting dimension, which sets the spacing for the two fastener points during layout and drilling.
The EPCO DP412-BZ pull has an overall length of 3-7/8 inch, which keeps the tab compact while still providing enough length for a defined finger grip area at the edge.
The tab pull is specified for 3/4 inch material thickness, which matches standard cabinet doors and drawer fronts so the flush mortise mount sits correctly in the edge.
The flush mortise mounting recesses the pull body into the door or drawer edge, which keeps the face profile flatter and reduces projection into adjacent walkways.
The pull has an anodized satin bronze finish, which gives the metal a controlled bronze tone that coordinates with other satin bronze decorative hardware on the project.
The EPCO DP412-BZ tab pull uses #6 x 5/8 inch screws at the 3 inch centers, which secure the pull through the 3/4 inch cabinet material in a typical installation.
The EPCO 3 inch satin bronze tab pull with 3 inch center to center spacing and 3-7/8 inch overall length gives a defined, low-profile edge grip that coordinates across multiple doors and drawers. The flush mortise mounting on 3/4 inch material keeps cabinet faces clean while the anodized satin bronze finish aligns with other satin bronze decorative hardware. For projects using standard 3/4 inch cabinet stock where a compact, recessed tab pull is required, this EPCO DP412-BZ model offers a consistent layout based on its 3 inch centers, fixed length, and defined finish.
Sold In: 1 Each