Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO edge pull Edge Series DP41-A-4 is a back mounted aluminum tab pull that creates a low-profile grip along the door or drawer edge. The 2 inch center to center drilling sets the pull spacing, so layout stays consistent across a run of fronts. The 4 inch overall length gives enough finger contact along the edge while keeping the hardware compact on smaller fronts. The 1-9/16 inch projection defines how far the pull stands off the face, setting a clear handhold without crowding adjacent fronts. Anodized satin clear aluminum finish provides a neutral metallic look that pairs with many cabinet finishes. The pull is designed for material thickness from 1/2 inch to 7/8 inch, so it matches common cabinet door and drawer stock while maintaining proper engagement on the edge.
This EPCO edge pull installs as a back mounted tab pull, so the hardware references from the door or drawer edge for alignment. The 2 inch center to center measurement guides drilling of the mounting holes, which supports repeatable spacing when installing multiple pulls. With a design suited for 1/2 inch to 7/8 inch thick material, the pull grips the edge of common cabinet stock while keeping the tab proportionate to the panel thickness. The 4 inch overall length and 1-9/16 inch projection work together to provide a defined handhold along the edge, which matters when setting consistent ergonomics across a kitchen, bath, or casework run.
This EPCO Edge Series DP41-A-4 works as a decorative handle within the handles and pulls category, suited to cabinet doors and drawers that match its 1/2 inch to 7/8 inch material thickness range. The back mounted format positions the pull at the panel edge, so it functions well on modern slab fronts where an edge grip is preferred over a projecting traditional handle. Wurth Baer Supply offers this pull as part of its decorative hardware and moldings selection, placing it in workflows where installers coordinate pulls with other cabinet hardware. The 2 inch center to center layout matches a compact drilling pattern, which is useful on narrower drawer fronts or smaller doors that cannot accept wider spacing.
The 4 inch overall length gives this tab pull a footprint that spans a useful portion of the edge without overpowering smaller fronts, keeping the visual line clean on contemporary cabinetry. Anodized satin clear aluminum finish supports use in projects where a straightforward metallic appearance is desired, tying in with other aluminum components. Because it is sold in each quantities, the pull can be specified per opening, which helps match hardware counts closely to cabinet layouts. Within the EPCO product class, this handle serves as a specific option when a low-profile edge pull is required instead of a full-width bar pull.
The 1-9/16 inch projection on this EPCO edge pull determines how far the gripping surface stands off the cabinet face, affecting how fingers locate the pull from different angles. This projection supports a defined handhold while still keeping the assembly close to the front, which is important along tight runs of doors and drawers. The design for 1/2 inch to 7/8 inch material thickness ties directly to common cabinet construction, helping the pull sit proportionally on both thinner stock and standard face-frame or frameless fronts.
The 2 inch center to center spacing also influences drilling efficiency, because a single jig setting can service multiple fronts when that pattern is used across a job. Combined with the 4 inch overall length, this spacing gives a balanced look and feel, offering enough grab area without requiring wider doors to carry oversized hardware. As an anodized satin clear aluminum component, the pull contributes a uniform surface that coordinates with other aluminum pieces in the build, assisting in achieving a consistent hardware appearance from cabinet to cabinet.
The EPCO edge pull uses a 2 inch center to center dimension, which sets the drilling pattern and helps keep hole spacing consistent on multiple cabinet fronts.
The DP41-A-4 aluminum tab pull is 4 inches in overall length, giving a compact but usable gripping area on doors and drawers.
The EPCO tab pull is suited for material thickness from 1/2 inch to 7/8 inch, aligning with typical cabinet door and drawer stock dimensions.
The aluminum edge pull has a 1-9/16 inch projection, defining the stand-off distance and finger clearance from the cabinet surface.
The EPCO Edge Series DP41-A-4 has an anodized satin clear aluminum finish, giving a neutral metallic look that coordinates with many cabinet styles.
This EPCO edge pull is back mounted, so it fastens through the panel and references the edge, aiding alignment along cabinet doors and drawers.
The EPCO edge pull DP41-A-4 combines a 2 inch center to center layout, 4 inch overall length, and 1-9/16 inch projection to create a compact, functional grip along cabinet edges. With its anodized satin clear aluminum finish and fit for 1/2 inch to 7/8 inch thick material, it works within common cabinet construction and decorative hardware plans. For projects calling for a low-profile, back mounted tab pull from the EPCO Edge Series, this model offers defined dimensions that translate cleanly into drilling, layout, and day-to-day use.
Sold In: 1 Each