Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO Edge Series tab pull gives a low-profile grip for doors or drawers while keeping the front face clear, which helps maintain simple cabinet lines on modern jobs. This anodized satin brass tab pull provides a consistent brass finish that supports coordinated runs across a project. The 1 inch center to center mounting dimension sets a precise drilling pattern that speeds layout on multiple fronts. Its 1-1/2 inch overall length keeps the pull compact at the edge, which helps in tight banks of drawers or narrow doors. A 1-9/16 inch projection brings fingers away from the surface, which improves everyday grip without adding bulky hardware. Back mounted installation hides fasteners from the front, which supports a clean presentation on finished cabinetry. The pull is designed for material thickness of 1/2 to 7/8 inch, so it fits a common range of cabinet stock in shops and onsite work.
This EPCO Edge Series tab pull uses a back mounted attachment, so all fasteners engage from the rear of the door or drawer and leave only the tab visible on the front. Its 1 inch center to center dimension defines the exact distance between mounting points, which simplifies jig setup or gang drilling for production runs. With a 1-1/2 inch overall length, the pull locates near the panel edge while staying compact, helping it sit properly on narrow stiles and rails. The 1-9/16 inch projection sets how far the pull stands off the face, which affects both reach and clearance around adjacent components. The design is specified for material thickness between 1/2 and 7/8 inch, so it installs into common cabinet door and drawer front constructions without needing different pull sizes.
This EPCO Edge Series 1 inch center to center tab pull fits projects that call for a compact, edge-mounted grip on standard cabinet materials. Its suitability for 1/2 to 7/8 inch thick material means it works on many cabinet doors and drawer fronts built from common sheet goods and solid stock. The 1-1/2 inch overall length keeps the pull close to the edge, which is useful on narrow rails where space is limited. Because mounting is from the back, the pull is well suited to visible kitchen, bath, or casework fronts where uninterrupted surfaces are important. The anodized satin brass finish supports use where a brass tone is part of the design palette.
The defined 1 inch center to center mounting distance allows installers to use simple templates or stops for drilling, which helps maintain consistent hardware alignment across long cabinet runs. The back mounted configuration means all holes stay on a known pattern from the edge, which aids in layout when duplicating the same setup on multiple doors or drawers. With a 1-9/16 inch projection, the pull stands off enough to provide hand clearance, which matters on heavier doors that see frequent use. The material thickness range of 1/2 to 7/8 inch narrows the application window, which helps predict how the pull will seat against the edge across different cabinet lines. The EPCO DP41-B designation ties these measurements and finish together under a single part number, which simplifies reordering and matching parts on future phases or repair work.
The EPCO Edge Series DP41-B tab pull has 1 inch center to center, 1-1/2 inch overall length, and 1-9/16 inch projection, which defines drilling layout and how far it stands off the cabinet face.
The back mounted EPCO tab pull attaches from the rear of the door or drawer, which keeps the front face free of visible fasteners for a clean, uninterrupted look on finished cabinetry.
The EPCO Edge Series DP41-B tab pull is specified for 1/2 to 7/8 inch material thickness, which covers many standard cabinet doors and drawer fronts used in shop-built and manufactured work.
The 1 inch center to center spacing on this EPCO tab pull provides a simple, repeatable drilling pattern, which supports straightforward jig use and consistent alignment across multiple fronts.
The EPCO Edge Series DP41-B tab pull has an anodized satin brass finish, which delivers a controlled brass tone and sheen for coordinated hardware runs on cabinets.
The 1-9/16 inch projection sets how far the pull extends from the cabinet face, which affects finger clearance and helps provide a comfortable grip during regular door and drawer operation.
The EPCO Edge Series DP41-B tab pull brings defined dimensions and a consistent anodized satin brass finish to cabinet fronts, which streamlines both layout and visual results. Its 1 inch center to center spacing, 1-1/2 inch overall length, and 1-9/16 inch projection give clear reference points for drilling and positioning. With a back mounted design and fit for 1/2 to 7/8 inch material, it suits many standard cabinet constructions. Use this part where a compact brass tab pull is needed to keep faces clean while maintaining a dependable grip.
Sold In: 1 Each