Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO Edge Series tab pull provides a low-profile way to open cabinet doors and drawers, using a compact 3 inch overall length that suits small fronts and tight layouts. The 2 inch center to center dimension sets consistent hole spacing, which simplifies layout and drilling across multiple cabinets on a run. An anodized satin brass finish adds a warm metallic look, while the anodizing process treats the aluminum surface to support long-term appearance in typical interior woodworking environments. Back mounted construction keeps fasteners concealed behind the door or drawer front, giving a clean visual line on the working face. The pull is designed for material thickness from 1/2 inch to 7/8 inch, so it works across common cabinet door and drawer stock sizes. A 1-9/16 inch projection gives fingers room to grab the edge comfortably without extending too far into the walkway.
This EPCO Edge Series tab pull uses a back mounted configuration, so it fastens from the rear of the cabinet door or drawer front and leaves only the pull visible at the edge. The 2 inch center to center dimension determines the spacing between the two mounting points, guiding drilling layout for accurate placement. Material thickness compatibility from 1/2 inch to 7/8 inch means the pull is engineered to sit correctly on common cabinet stock without overhanging too far or feeling shallow at the edge. A 3 inch overall length positions the grip along a short section of the door or drawer, which can help installers place it clear of hinge areas or other hardware. With 1-9/16 inch projection, the pull extends just enough to grip comfortably while staying close to the cabinet face line.
The EPCO Edge Series 2 inch center to center anodized satin brass tab pull is suited to cabinet doors and drawers that accept back mounted pulls. Its 3 inch overall length fits well on standard kitchen, bath, or shop fronts where a short pull is desired along the top or side edge. Material thickness compatibility from 1/2 inch to 7/8 inch lets this pull serve on typical solid, plywood, or composite fronts used in many woodworking projects. The satin brass anodized finish coordinates visually with other satin brass decorative hardware, allowing a consistent look across handles and pulls in the same space. Because the projection is 1-9/16 inch, the pull offers enough space for fingers on frequently used cabinet fronts without taking excessive room in front of the face frame or case.
The 2 inch center to center tab pull layout allows installers to use the same drilling template across multiple doors and drawers, which speeds production and keeps hardware lines straight. The back mounted cabinet tab pull design sets the fastener entry on the rear of the panel, so front surfaces remain uninterrupted for a modern, edge-grab look. Material range from 1/2 inch to 7/8 inch means the bend and grip geometry of the pull are sized so the finger area sits in a predictable spot relative to the door or drawer edge. The 3 inch aluminum edge pull length helps position the pull on smaller panels without overlapping stile joints or meeting rails. Anodized satin brass finish on aluminum provides a controlled surface color, which supports visual consistency when multiple DP41-B-3 edge pulls are installed in a row.
The EPCO Edge Series tab pull has a 2 inch center to center dimension, 3 inch overall length, and 1-9/16 inch projection, which together define its footprint and how far it stands off the cabinet face.
The back mounted design places fastener entry on the rear of the door or drawer front, leaving only the pull visible at the edge for a clean, modern appearance on the working face.
The DP41-B-3 edge pull is specified for material thickness from 1/2 inch to 7/8 inch, so it matches common cabinet door and drawer front stock used in many woodworking projects.
The 2 inch center to center spacing sets a fixed distance between mounting points, allowing use of a repeating drilling pattern or template for consistent alignment across multiple fronts.
This EPCO decorative cabinet pull has an anodized satin brass finish, which provides a satin brass color tone on the aluminum body for coordinated cabinet hardware appearances.
The tab pull projects 1-9/16 inch from the cabinet front, offering finger clearance for a comfortable grip while keeping the hardware close to the cabinet face line.
The EPCO Edge Series tab pull with 2 inch center to center spacing, 3 inch overall length, and 1-9/16 inch projection gives a defined, repeatable footprint for cabinet hardware layouts. Its anodized satin brass finish on aluminum supports a coordinated appearance across doors and drawers. Material thickness compatibility from 1/2 inch to 7/8 inch means one model can serve multiple cabinet front constructions. Selecting this DP41-B-3 edge pull lets installers and woodworkers standardize on a compact, back mounted grip that suits many interior cabinet projects.
Sold In: 1 Each