EPCO Edge Series tab pull gives a low-profile way to open doors and drawers while keeping cabinet faces clear. The 2 inch center to center spacing sets a compact grip point, useful on smaller fronts or tight layouts. The 4 inch overall length provides enough finger contact for a steady pull without crowding adjacent hardware. Anodized satin brass finish adds a warm metallic look that reads modern but still suits many wood tones. Aluminum construction keeps the pull light, which helps when multiples are installed across a run of doors. Back mounted design keeps all fasteners behind the panel, leaving the front edge clean for a simple visual line. This pull works as a practical choice when you want consistent sizing from piece to piece on a project.
The 2 inch center to center spacing defines the drilling pattern, so installers can lay out repeated locations with simple jigs or templates. With 4 inch overall length, the pull extends past the hole pair, giving some forgiveness in edge placement while still covering drilled locations. Back mounted style means work happens from the rear of the panel, so installers can mark, drill, and fasten without disturbing finished front faces. Designed for material from 1/2 to 7/8 inch thick, this pull fits typical cabinet doors and drawer fronts, which keeps planning straightforward on standard carcass constructions. The 1 and 9 16 inch projection helps fingers clear the edge during use, reducing contact with the cabinet surface over repeated openings.
This anodized satin brass tab pull works on cabinet doors and drawer fronts that fall between 1/2 and 7/8 inch thick, matching common kitchen, bath, and built-in casework materials. The EPCO Edge Series form mounts at the panel edge, so it suits frameless cabinets and applications where you want hardware located right at the front corner. With 2 inch center to center mounting, the pull fits smaller door widths and narrow drawer fronts without overwhelming the scale. The 4 inch overall length allows use on wider fronts in pairs or centered, supporting consistent sightlines along a run. Its aluminum body with anodized finish suits interior woodworking environments where metal pulls are preferred for daily handling. The satin brass tone helps define the touch point, assisting users in quickly locating the grip along flush cabinet faces.
The defined 2 inch center to center measurement lets shops set up drilling fixtures once and repeat them across multiple fronts, helping maintain alignment from cabinet to cabinet. The 4 inch overall length offers enough surface to absorb slight variation in edge offset while still covering the fastener line, which supports clean visual results when fronts vary slightly. Back mounted design puts the fastening work on the inside face, so finished fronts stay undisturbed during drilling and driving, which aids in maintaining surface quality. The 1 and 9 16 inch projection gives consistent finger clearance along the edge, reducing the chance of users dragging hands against cabinet surfaces over time. The fit window for 1/2 to 7/8 inch thick material allows one pull specification to serve many panel thicknesses in a project, streamlining ordering and layout decisions. Anodized satin brass finish provides a stable surface color, helping multiple pulls read uniformly when installed in long banks of doors and drawers.
The EPCO Edge Series tab pull has a 2 inch center to center dimension, so drill holes are spaced 2 inches apart, which simplifies jig setup for repeated cabinet fronts.
The EPCO Edge Series tab pull has a 4 inch overall length, giving users a broader gripping area while still working on smaller cabinet doors and drawers.
The EPCO Edge Series tab pull projects 1 and 9 16 inch from the mounting surface, creating enough clearance for fingers to hook behind the edge comfortably.
The EPCO Edge Series tab pull is back mounted, so fasteners go through the rear of the cabinet panel, keeping the front edge visually clean.
The EPCO Edge Series tab pull is designed for material thickness from 1/2 to 7/8 inch, aligning with common cabinet door and drawer front sizes.
The EPCO Edge Series tab pull is aluminum with an anodized satin brass finish, giving a warm metal appearance suited to interior cabinet applications.
The EPCO Edge Series tab pull with 2 inch center to center spacing and 4 inch overall length offers a defined layout for cabinet doors and drawers. Anodized satin brass on an aluminum body supports a consistent look across multiple fronts. Back mounted installation keeps faces clear, while design for 1/2 to 7/8 inch material suits standard cabinet construction. Use this DP41-B-4 edge pull when you want a compact, repeatable grip detail along cabinet edges.
Sold In: 1 Each