Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO Edge Series tab pull gives you a low-profile way to open cabinet doors and drawers while keeping the front face clear. This DP41-B-6 model has a 4 inch center to center dimension, so it lines up with a standard 4 inch drilling pattern on new or replacement work. The overall length of 6 inches leaves grip area past the screw locations, which helps when pulling heavier drawers. A 1-9/16 inch projection creates enough finger clearance for everyday use while still keeping the hardware tight to the cabinet for a streamlined look. The pull is back mounted, so it fastens from the inside of the door or drawer front and leaves only the tab visible on the outside. It is designed for material thickness of 1/2 inch to 7/8 inch, matching common cabinet construction ranges in both shop-built and manufactured cabinets.
This EPCO Edge Series tab pull installs as a back mounted pull, so it fastens from the inside face of the door or drawer front into the body of the pull. The 4 inch center to center dimension guides drilling or boring for the mounting points, giving a fixed reference for layouts across multiple fronts. With an overall length of 6 inches, the pull positions beyond the drilled area, which helps with consistent placement along door or drawer edges. The pull is designed for material thickness from 1/2 inch to 7/8 inch, so it seats properly on edges within that range without overhanging too far or sitting too shallow. Projection of 1-9/16 inches defines how far the tab stands off the face, setting finger clearance once mounted.
This EPCO Edge Series tab pull is part of the EPCO decorative hardware and moldings handles and pulls class, so it is intended for use on cabinetry and similar casework. The anodized satin brass finish gives it a decorative appearance that suits furniture-style cabinets, vanities, and built-ins where a flush, edge-mounted grip is preferred. With a 4 inch center to center drilling pattern and 6 inch overall length, it works where a linear, horizontal tab is needed along an edge. The 1-9/16 inch projection defines how far it extends from the surface, which establishes the feel of the pull along the door or drawer edge in regular use.
The fixed 4 inch center to center dimension on this DP41-B-6 tab pull supports consistent spacing across banks of doors and drawers, which is important when repeating pulls along a run of cabinets. The 6 inch overall length gives a predictable tab length along each edge, so visual alignment stays uniform from cabinet to cabinet. Because the design is for material thickness of 1/2 inch to 7/8 inch, the same pull can be used on doors and drawer fronts within that thickness range without changing model numbers. The back mounted construction keeps the visible hardware limited to the tab itself, so once positions are established, the same look carries through on every installation.
The EPCO Edge Series tab pull DP41-B-6 has a 4 inch center to center dimension, a 6 inch overall length, and a 1-9/16 inch projection, which together define drilling layout and how far the pull stands off the cabinet.
The back mounted design of this tab pull means mounting is from the inside face of the door or drawer front, leaving only the anodized satin brass tab visible on the outside for a clean edge appearance.
The DP41-B-6 pull is designed for material thickness from 1/2 inch to 7/8 inch, so it fits typical cabinet doors and drawer fronts built within that thickness range.
This EPCO cabinet tab pull has an anodized satin brass finish, giving a brass-colored, satin-sheen appearance suited for decorative hardware and moldings applications on cabinets.
The 4 inch center to center measurement provides a standard drilling reference, which simplifies repeating hole locations on multiple fronts when laying out cabinet hardware.
The anodized satin brass edge pull has a 1-9/16 inch projection, which sets finger clearance and determines how far the tab extends from the cabinet face in daily use.
The EPCO Edge Series tab pull DP41-B-6 combines a 4 inch center to center drilling dimension, 6 inch overall length, and 1-9/16 inch projection in an anodized satin brass finish. Designed for material thickness between 1/2 inch and 7/8 inch, it aligns with common cabinet doors and drawer fronts. For projects calling for a back mounted, edge-style grip with a consistent layout across multiple fronts, this tab pull provides defined dimensions that support repeat work.
Sold In: 1 Each