Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO edge series 1 inch tab pull is a compact handle designed to give a clean pull point on cabinet doors and drawers while staying tight to the front. The 1 inch center to center dimension sets a small, precise grip span that works well on narrow fronts or where a minimal pull is needed. The 1-1/2 inch overall length keeps the hardware visually light, so it supports simple, modern layouts without overpowering the panel. An anodized brushed brass finish provides a warm metallic look while the anodizing treats the aluminum surface, which supports consistent color and feel across multiple pulls. The back mounted design anchors the pull from the rear face of the material, so the front shows only the tab and no visible fastener heads. This layout lets installers align multiple pulls in a straight line and maintain a clean, repeatable appearance on finished runs.
The EPCO DP41-BBR pull uses a back mounted layout, so fasteners go through the cabinet material into the pull body from the rear side. This method keeps the visible edge focused on the anodized brushed brass tab, supporting clean lines on the cabinet face. A projection of 1-9/16 inches sets the working clearance, giving space behind the tab for fingers while keeping the grip close enough to the surface for tight installations. The center to center distance at 1 inch defines the drilling pattern, which matters when matching this pull with predrilled fronts or routing jigs. With an overall length of 1-1/2 inches, the pull fits short edges and smaller faces, allowing a consistent hardware style on both small and standard-width fronts in the same run.
This anodized brushed brass tab pull is set up for back mounting on cabinet doors or drawers where a subtle edge grip is preferred. Because the center to center distance is 1 inch, it suits tight spaces like narrow drawer fronts or compact door rails, giving a defined grab point without crowding nearby hardware or trim. The 1-1/2 inch overall length lets it sit neatly on short edges, so it works on both small accessory fronts and larger cabinets that need a minimal pull. With a 1-9/16 inch projection, the pull stands off the front enough for fingers to wrap behind the tab, which supports everyday opening and closing without strain on fingertips. As part of an edge-style layout, the pull places the hand close to the door edge, helping doors swing and drawers slide smoothly under normal use.
The 1 inch center to center spacing on this EPCO edge series 1 inch tab pull gives installers a fixed drilling reference, so repeated holes line up accurately across a bank of cabinets. The 1-1/2 inch overall length defines the footprint on the edge, allowing repeatable positioning relative to the corner or end of the panel. A projection of 1-9/16 inches sets the pull-out distance, so installers can anticipate clearance for adjacent doors or wall surfaces when laying out hardware locations. The anodized brushed brass finish treats the aluminum surface, which supports a uniform appearance from piece to piece and helps maintain a consistent brushed texture across an installation. Using a back mounted design, the pull anchors from behind the material, allowing the front face to remain free of exposed fasteners and creating a clean, aligned row of tabs on finished cabinetry.
The EPCO edge series 1 inch tab pull has a 1 inch center to center dimension, which sets a tight mounting pattern useful for narrow cabinet fronts or small drawers.
The EPCO DP41-BBR edge pull has an overall length of 1-1/2 inches, so it stays compact on the door or drawer edge while still providing a defined grip tab.
This anodized brushed brass tab pull has a projection of 1-9/16 inches, giving space for fingers to engage behind the tab while keeping the hardware close to the cabinet face.
The EPCO edge series 1 inch tab pull is back mounted, so fasteners pass through the cabinet material into the pull from the rear, leaving the front face clean.
This tab pull is designed for material thickness of 1/2 inch to 7/8 inch, which covers many common cabinet door and drawer front constructions.
The EPCO DP41-BBR pull has an anodized brushed brass finish, giving a brushed brass appearance that coordinates with similar decorative hardware finishes.
The EPCO edge series 1 inch tab pull combines a compact 1 inch center to center layout, 1-1/2 inch overall length, and 1-9/16 inch projection to support neat, repeatable cabinet hardware runs. The anodized brushed brass finish and back mounted design keep the visible edge clean, so the focus stays on the cabinet lines rather than fastener heads. With suitability for material thickness from 1/2 inch to 7/8 inch, this pull aligns with common cabinet door and drawer constructions. Choosing this EPCO DP41-BBR tab pull lets you match size, finish, and mounting details to projects that call for a low-profile edge grip.
Sold In: 1 Each