Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO Edge Series 4 inch tab pull gives you a low-profile way to open doors and drawers using a 4 inch (102 mm) center to center layout, so hole spacing stays consistent on a bank of cabinets. The 6 inch overall length extends past the screw locations, which creates a comfortable gripping area at the edge while keeping the hardware visually balanced on wider fronts. An anodized brushed brass finish adds a brushed brass look while the anodized layer helps the surface stand up to regular cabinet handling. The pull is back mounted, so it anchors from the inside of the door or drawer front, leaving the exterior face clean and uninterrupted. A projection of 1-9/16 inches gives enough finger clearance at the edge, which helps users grab the pull easily without crowding their hand against the cabinet face.
This EPCO decorative pull uses a 4 inch center to center layout, which lets fabricators measure and drill two mounting holes on a 4 inch spread to align with the pull legs. Back mounting means the installer bores through the door or drawer front, then secures the pull from the interior side so the exterior edge stays clean. The 1-9/16 inch projection defines both the grip depth and how far the hardware stands off the cabinet edge, helping installers plan clearances near adjacent fronts. Designed for material thickness from 1/2 inch to 7/8 inch, this pull fits common door and drawer front builds, which streamlines planning when different cabinets in the same project use similar stock thicknesses.
This EPCO Edge Series tab pull suits cabinet doors and drawers that can accept back mounting, because it fastens from the inside through the front material. The 6 inch overall length gives proportion on doors and drawers that use a 4 inch center to center layout, so the visible pull extends slightly past the fastener spread for a finished edge detail. Its design for 1/2 inch to 7/8 inch material thickness means it fits many standard cabinet fronts, allowing installers to use the same pull across matching upper cabinets, base cabinets, and drawer stacks that share those thicknesses. An anodized brushed brass finish lets the pull coordinate with other brushed brass decorative hardware in the same space, supporting a consistent appearance along a full run of cabinetry.
The clearly defined 4 inch (102 mm) center to center spacing on this DP41-BBR-6 pull allows jigs or templates to be set once, which speeds drilling and keeps every pull aligned from cabinet to cabinet. Its 1-9/16 inch projection gives fabricators a known offset from the cabinet face, helping layout when doors open near walls, appliances, or adjacent panels where clearance matters. Designing the pull for 1/2 inch to 7/8 inch material thickness gives a predictable clamping range, which helps when specifying hardware for frameless or face-frame cabinets that fall in this thickness window. The back mounted configuration means all fastener engagement occurs through the cabinet front from the inside, which keeps the edge profile smooth and consistent and supports a clean look on modern projects.
The EPCO DP41-BBR-6 pull has a 4 inch (102 mm) center to center dimension, which sets the hole spacing for drilling and keeps pulls aligned consistently across cabinets.
The EPCO Edge Series DP41-BBR-6 has a 6 inch overall length, so the pull extends slightly past the mounting holes to provide a comfortable grip area along the edge.
The DP41-BBR-6 tab pull is designed for material thickness of 1/2 inch to 7/8 inch, covering many standard cabinet door and drawer front constructions in shop and factory work.
The EPCO brushed brass pull has a projection of 1-9/16 inches, providing finger clearance for gripping while controlling how far the hardware extends from the cabinet edge.
The EPCO DP41-BBR-6 is back mounted, so it fastens through the door or drawer front from the rear, leaving the front edge clean and visually uncluttered.
The EPCO Edge Series DP41-BBR-6 features an anodized brushed brass finish, giving a brushed brass appearance with an anodized surface suited to decorative hardware use.
The EPCO Edge Series 4 inch tab pull with 6 inch overall length, 1-9/16 inch projection, and 4 inch center to center layout gives installers defined dimensions to work from on cabinet projects. Its back mounted design and fit for 1/2 inch to 7/8 inch material allow it to serve a wide range of cabinet doors and drawers that share similar thicknesses. The anodized brushed brass finish lets this DP41-BBR-6 model align with brushed brass decorative hardware selections. Select this pull when a consistent edge profile and repeatable mounting pattern are priorities across a run of cabinetry.
Sold In: 1 Each