EPCO Edge Series 2 inch tab pull gives you a compact aluminum handle that mounts at the edge of the door or drawer, so you gain a clean look while still having a positive gripping point. The 2 inch center to center drilling provides a small, consistent footprint across multiple fronts, which helps layout go faster on runs of doors or drawers. The 3 inch overall length keeps the pull short enough for tight cabinet faces while still offering enough finger space to grab. An anodized brushed bronze finish delivers a bronze tone on an aluminum body, bringing a finished look that matches brushed bronze hardware lines. This pull is part of the EPCO Edge Series, so it is designed as a tab-style pull that works off the door edge instead of the face, which matters when you want a minimal projection of hardware on modern and flat-panel cabinetry.
This EPCO tab pull is back mounted, so the fastening points are accessed from the rear of the door or drawer front, which matters when planning boring patterns and assembly order. With a center to center of 2 inches and an overall length of 3 inches, the pull aligns well on typical cabinet modules, allowing you to maintain even reveals without the hardware dominating the panel. The 1-9/16 inch projection defines how far the pull projects from the edge, giving enough clearance to grasp from above or below. This pull is specified for material thickness of 1/2 inch to 7/8 inch, which covers many cabinet door and drawer front thicknesses used in kitchen, bath, and casework projects, allowing you to keep one style across a job.
The EPCO Edge Series 2 inch tab pull is designed for cabinet doors and drawers where an edge-mounted pull is preferred, so it suits applications that call for minimal hardware on the face. Its 2 inch center to center layout concentrates the mounting near the edge, which works well on narrower fronts often found in upper cabinets or small drawer banks. The specified 1/2 inch to 7/8 inch material thickness range aligns with many common cabinet construction methods, from thinner slab doors to thicker drawer fronts, which lets you repeat the same pull across different cabinet components. The 1-9/16 inch projection gives enough stand-off so fingers can hook behind the pull from the top or side, which is useful on base cabinets, wall cabinets, and smaller utility pieces where access angles vary around appliances or walls.
The 3 inch overall length of this aluminum edge pull provides a fixed reference when setting reveals and spacing, which helps installers keep pulls aligned along long cabinet runs without constant re-measuring. The anodized brushed bronze finish offers a stable, brushed bronze appearance on aluminum, which helps coordinate hardware across a project while keeping the visual line of the pulls consistent from unit to unit. The back mounted configuration hides the fasteners from the front edge, which creates a uninterrupted look along the cabinet line and reduces visual distractions on flat or slab doors. Using the defined 2 inch center to center dimension, installers can standardize drilling templates, which streamlines shop setup for repetitive production and reduces layout time on site when replacing or upgrading existing pulls to this specific DP41-BBZ-3 model.
The EPCO Edge Series 2 inch tab pull has a 2 inch center to center, a 3 inch overall length, and a 1-9/16 inch projection, which defines drilling layout and how far it stands off the cabinet.
The back mounted EPCO DP41-BBZ-3 tab pull fastens from the rear of the door or drawer, which leaves no visible fasteners on the front edge and supports a clean finished appearance.
The EPCO Edge Series 2 inch tab pull is designed for material thickness from 1/2 inch to 7/8 inch, which covers many standard cabinet door and drawer front constructions.
The EPCO DP41-BBZ-3 tab pull uses an anodized brushed bronze finish on aluminum, which delivers a brushed bronze appearance that coordinates with other brushed bronze decorative hardware.
The 1-9/16 inch projection spaces the pull off the cabinet surface, which creates finger clearance for a comfortable grip without pushing the pull too far into walk paths.
The manufacturer part number is DP41-BBZ-3, which identifies this specific anodized brushed bronze, 2 inch center to center, 3 inch overall length EPCO Edge Series tab pull.
The EPCO Edge Series 2 inch tab pull combines a 2 inch center to center layout, 3 inch overall length, and 1-9/16 inch projection, giving you predictable dimensions to plan drilling and alignment on cabinet doors and drawers. Its anodized brushed bronze finish on aluminum and back mounted design support a clean, modern presentation across kitchen, bath, and casework projects. For projects needing an edge-mounted handle that fits 1/2 inch to 7/8 inch material thickness, this DP41-BBZ-3 pull offers a repeatable solution that matches standard cabinet construction and decorative hardware in a brushed bronze look.
Sold In: 1 Each